DIAMOND FLOWER INC.
MIO-400KF, MIO-400KF REV. C
|
|
Data bus: 16-bit, ISA
Size: Half-length, full-height card
Hard drives supported: Two IDE (AT) Interface drives
Floppy drives supported: Two 360KB, 720KB, 1.2MB, or 1.44MB drives
|
CONNECTIONS | |
|
Function |
Location |
|
4-pin connector - drive active LED |
J1 |
|
34-pin data cable connector - floppy drive |
J2 |
|
16-pin game port |
J3 |
|
10-pin serial port 2 - internal |
J4 |
|
40-pin IDE (AT) connector |
J5 |
|
9-pin serial port 1 - external |
J6 |
|
25-pin parallel port - external |
J7 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Location |
Setting | |
| » |
Hard drive enabled |
JP3/H |
Pins 2 & 3 closed |
|
Hard drive disabled |
JP3/H |
Pins 1 & 2 closed | |
| » |
Game port enabled |
JP3/I |
Pins 2 & 3 closed |
|
Game port disabled |
JP3/I |
Pins 1 & 2 closed | |
|
USER CONFIGURABLE SETTINGS (CONTINUED) | |||
|
Function |
Location |
Setting | |
| » |
Serial Port 2 is DTE (Data Terminal Equipment) |
JP4 |
1 & 2, 3 & 4, 5 & 6, 7 & 8, 9 & 10 |
|
Serial Port 2 is DCE (Data Comm. Equipment) |
JP4 |
1 & 3, 2 & 4, 5 & 7, 6 & 8, 9 & 10 | |
| » |
Serial Port 1 is DTE |
JP5 |
1 & 2, 3 & 4, 5 & 6, 7 & 8, 9 & 10 |
|
Serial Port 1 is DCE |
JP5 |
1 & 3, 2 & 4, 5 & 7, 6 & 8, 9 & 10 | |
|
Note: Designated pins should be in closed position | |||
|
SERIAL PORT 1 SIGNAL STATUS | |||
|
Function |
Location |
Setting | |
| » |
DCD (Data Carrier Detect) - Normal |
JP1/A |
Pins 1 & 2 closed |
|
DCD (Data Carrier Detect) - Forced True |
JP1/A |
Pins 2 & 3 closed | |
| » |
DSR (Data Set Ready) - Normal |
JP1/B |
Pins 1 & 2 closed |
|
DSR (Data Set Ready) - Forced True |
JP1/B |
Pins 2 & 3 closed | |
| » |
CTS (Clear To Send) - Normal |
JP1/C |
Pins 1 & 2 closed |
|
CTS (Clear To Send) - Forced True |
JP1/C |
Pins 2 & 3 closed | |
|
SERIAL PORT 2 SIGNAL STATUS | |||
|
Function |
Location |
Setting | |
| » |
DCD (Data Carrier Detect) - Normal |
JP2/A |
Pins 1 & 2 closed |
|
DCD (Data Carrier Detect) - Forced True |
JP2/A |
Pins 2 & 3 closed | |
| » |
DSR (Data Set Ready) - Normal |
JP2/B |
Pins 1 & 2 closed |
|
DSR (Data Set Ready) - Forced True |
JP2/B |
Pins 2 & 3 closed | |
| » |
CTS (Clear To Send) - Normal |
JP2/C |
Pins 1 & 2 closed |
|
CTS (Clear To Send) - Forced True |
JP2/C |
Pins 2 & 3 closed | |
|
PARALLEL PORT CONFIGURATION | |||
|
LPT |
JP3/A |
JP3/B | |
|
LPT1 (3BCh) |
Pins 1 & 2 closed |
Pins 2 & 3 closed | |
| » |
LPT2 (378h) |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
LPT3 (278h) |
Pins 2 & 3 closed |
Pins 1 & 2 closed | |
|
Disabled |
Pins 1 & 2 closed |
Pins 1 & 2 closed | |
|
SERIAL PORT(S) CONFIGURATION | |||||||
|
Serial Port 1 |
Serial Port 2 |
JP3/C |
JP3/D |
JP3/E |
JP8/A |
JP8/B | |
| » |
COM1 |
COM2 |
2 & 3 |
2 & 3 |
2 & 3 |
Closed |
Closed |
|
COM2 |
COM3 |
2 & 3 |
2 & 3 |
1 & 2 |
Closed |
Open | |
|
COM1 |
COM4 |
2 & 3 |
2 & 3 |
2 & 3 |
Open |
Closed | |
|
COM3 |
COM4 |
2 & 3 |
2 & 3 |
2 & 3 |
Open |
Open | |
|
COM1 |
Disabled |
2 & 3 |
1 & 2 |
2 & 3 |
Closed |
Closed | |
|
Disabled |
COM2 |
1 & 2 |
2 & 3 |
2 & 3 |
Closed |
Closed | |
|
Disabled |
Disabled |
1 & 2 |
1 & 2 |
1 & 2 |
Closed |
Closed | |
|
Note: Pins designated should be in the closed position. | |||||||
|
FLOPPY DRIVE CONFIGURATION | |||
|
Drive |
JP3/F |
JP3/G | |
| » |
Floppy drive enabled |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
Floppy drive disabled |
Pins 1 & 2 closed |
Pins 2 & 3 closed | |
|
SERIAL PORT 1 IRQ SELECTION | |||||
|
IRQ |
JP9/A |
JP9/B |
JP9/C |
JP9/D | |
|
IRQ2 |
Closed |
Open |
Open |
Open | |
| » |
IRQ3 |
Open |
Open |
Open |
Closed |
|
IRQ4 |
Open |
Open |
Closed |
Open | |
|
IRQ5 |
Open |
Closed |
Open |
Open | |
|
SERIAL PORT 2 IRQ SELECTION | |||||
|
IRQ |
JP9/E |
JP9/F |
JP9/G |
JP9/H | |
|
IRQ2 |
Closed |
Open |
Open |
Open | |
|
IRQ3 |
Open |
Open |
Open |
Closed | |
| » |
IRQ4 |
Open |
Open |
Closed |
Open |
|
IRQ5 |
Open |
Closed |
Open |
Open | |
|
PARALLEL PORT IRQ | |||
|
IRQ |
JP9/I |
JP9/J | |
| » |
IRQ7 |
Open |
Closed |
|
IRQ5 |
Closed |
Open | |