Data bus:	32-bit, VL-bus
Size:	Three/quarter-length, half-height card
Hard drive supported:	Two IDE (AT) Interface drives
Floppy drives supported:	Two 360KB, 720KB, 1.2MB, or 1.44MB drives

CONNECTIONS
Function	Location
34-pin control cable connector-floppy drive	J1
25-pin parallel port (LPT1/2) - external	J2
10-pin serial port 2 (COM2/4) - internal	J3
10-pin serial port 1 (COM1/3) - internal	J4
40-pin AT Interface (IDE) connector	J5
4-pin connector-Drive active LED	J6

USER CONFIGURABLE SETTINGS
Function		Location	Setting
»	IDE normal mode enabled	JP1	pins 1 & 2 closed
	IDE turbo mode enabled	JP1	pins 2 & 3 closed
»	Hard drive enabled	JP8	open
		JP21	pins 2 & 3 closed
	Hard drive disabled	JP8	closed
		JP21	pins 1 & 2 closed
»	Parallel Port (J2) uses IRQ7	JP9	pins 1 & 2 closed
	Parallel Port (J2) uses IRQ5	JP9	pins 2 & 3 closed
»	Floppy drive enabled	JP22	pins 2 & 3 closed
	Floppy drive disabled	JP22	pins 1 & 2 closed
»	Serial Port 1 (J4) uses IRQ4	JP23	pins 1 & 2 closed
	Serial Port 1 (J4) uses IRQ3	JP23	pins 2 & 3 closed
»	Serial Port 2 (J3) uses IRQ3	JP24	pins 1 & 2 closed
	Serial Port 2 (J3) uses IRQ4	JP24	pins 2 & 3 closed

IDE RECOVERY TIME
TIme		Jumper JP3	Jumper JP4
	120ns	pins 1 & 2 closed	pins 1 & 2 closed
	180ns	pins 2 & 3 closed	pins 1 & 2 closed
	240ns	pins 1 & 2 closed	pins 2 & 3 closed
»	300ns	pins 2 & 3 closed	pins 2 & 3 closed

SERIAL PORT 1 (J4) CONFIGURATION
Address		Jumper JP15	Jumper JP16
»	3F8h	pins 2 & 3 closed	pins 2 & 3 closed
	2F8h	pins 1 & 2 closed	pins 2 & 3 closed
	Disabled	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 1 & 2 closed	pins 1 & 2 closed

SERIAL PORT 2 (J3) CONFIGURATION
Address		Jumper JP17	Jumper JP18
»	2F8h	pins 2 & 3 closed	pins 2 & 3 closed
	3F8h	pins 1 & 2 closed	pins 2 & 3 closed
	Disabled	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 1 & 2 closed	pins 1 & 2 closed

PARALLEL PORT (J2) CONFIGURATION
Address		Jumper JP19	Jumper JP20
»	278h	pins 2 & 3 closed	pins 2 & 3 closed
	378h	pins 1 & 2 closed	pins 2 & 3 closed
	3BCh	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 1 & 2 closed	pins 1 & 2 closed

IRQ14 CONFIGURATION
Function		Jumper JP27	Jumper JP28
»	IRQ14 connected directly to bus	open	closed
	IRQ14 buffered mode enabled	closed	open

MISCELLANEOUS TECHNICAL NOTES

Jumper JP29 is factory configured - do not alter.