Data bus:	32-bit VL-Bus
Size:	Three/quarter-length, full-height card
Hard drive supported:	Four IDE (AT) interface drives
Floppy drives supported:	Two 360KB, 720KB, 1.2MB, or 1.44MB drives

CONNECTIONS
Function	Location
40-pin Primary IDE (AT) interface connector	CN1
40-pin Secondary IDE (AT) interface connector	CN2
34-pin control cable connector - floppy drive	CN3
16-pin game port - internal	CN4
10-pin serial port - internal	COMA
10-pin serial port - internal	COMB
2-pin connector - drive active LED	LED1
25-pin parallel port - external	P1

USER CONFIGURABLE SETTINGS
Function		Location	Setting
»	Factory configured - do not alter	W1	N/A
»	Factory configured - do not alter	W2	N/A
»	Factory configured - do not alter	W3	N/A
»	Factory configured - do not alter	W4	N/A
»	Factory configured - do not alter	W5	N/A
»	IOCHRDY 759AF select	W6/pins 2 & 3	closed
	IOCHRDY ISA select	W6/pins 1 & 2	closed
»	Primary IDE (AT) interface enabled	W8/pins 2 & 3	closed
	Primary IDE (AT) interface disabled	W8/pins 1 & 2	closed
»	Secondary IDE (AT) interface enabled	W9/pins 2 & 3	closed
	Secondary IDE (AT) interface disabled	W9/pins 1 & 2	closed
»	Speed 50MHz select	W10/pins 2 & 3	closed
	Speed 33MHz select	W10/pins 1 & 2	closed
»	Factory configured - do not alter	W13	N/A
»	Floppy drive order A:, B: normal	W26/pins 1 & 2	closed
	Floppy drive order A:, B: exchange	W26/pins 2 & 3	closed
»	Floppy drive address is 3F0h-3F7h	W27/pins 2 & 3	closed
	Floppy drive address is 370h-377h	W27/pins 1 & 2	closed
»	Floppy controller enabled	W28/pins 1 & 2	closed
	Floppy controller disabled	W28/pins 2 & 3	closed
»	Factory configued - do not alter	W32	N/A
»	Factory configured - do not alter	W33	N/A
»	Factory configured - do not alter	W34	N/A
»	Game port enabled	W46	closed
	Game port disabled	W46	open

IDE (AT) TIMMING & MODE CONFIGURATION
Timing	Mode	W11	W12
240ns	3	pins 1 & 2 closed	pins 1 & 2 closed
400ns	2	pins 1 & 2 closed	pins 2 & 3 closed
500ns	1	pins 2 & 3 closed	pins 1 & 2 closed
600ns	0	pins 2 & 3 closed	pins 2 & 3 closed

HARD DRIVE DMA SELECTION
Channel	W14	W15	W16	W17	W18	W19
5	open	open	closed	open	open	closed
6	open	closed	open	open	closed	open
7	closed	open	open	closed	open	open

SERIAL PORT 1 CONFIGURATION
COM		W20	W21
»	COM1 (3F8h)	pins 1 & 2 closed	pins 2 & 3 closed
	COM3 (3E8h)	pins 2 & 3 closed	pins 1 & 2 closed
	Not available	pins 1 & 2 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

SERIAL PORT 2 CONFIGURATION
COM		W22	W23
»	COM2 (2F8h)	pins 1 & 2 closed	pins 2 & 3 closed
	COM4 (2E8h)	pins 2 & 3 closed	pins 1 & 2 closed
	Not available	pins 1 & 2 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

PARALLEL PORT CONFIGURATION
LPT		W24	W25
»	LPT1 (378h)	pins 2 & 3 closed	pins 1 & 2 closed
	LPT2 (278h)	pins 1 & 2 closed	pins 2 & 3 closed
	LPT3 (3BCh)	pins 1 & 2 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

PARALLEL PORT MODE SELECTION
Mode	W29	W30
Printer	pins 1 & 2 closed	pins 1 & 2 closed
EPP/ECP	pins 1 & 2 closed	pins 2 & 3 closed
EPP/SPP	pins 2 & 3 closed	pins 1 & 2 closed
EXT2FDD	pins 2 & 3 closed	pins 2 & 3 closed

SERIAL PORT 1 INTERRUPT SELECTION
IRQ		W35	W36	W37
»	4	closed	open	open
	3	open	closed	open
	5	open	open	closed

SERIAL PORT 2 INTERRUPT SELECTION
IRQ		W38	W39	W40
»	3	closed	open	open
	4	open	closed	open
	5	open	open	closed

PARALLEL PORT INTERRUPT SELECTION
IRQ		W41	W42
»	7	closed	open
	5	open	closed

PRINTER OUTPUT CONFIGURATION
Setting	W43
Output	closed
Bi-directional	open

DMA SELECTION
Channel	W31	W44	W45
1	pins 1 & 2 closed	closed	open
3	pins 2 & 3 closed	open	closed