Data bus:	16-bit, ISA
Size:	Half-length, full-height card
Hard drive supported:	Two IDE(AT) interface drives
Floppy drives supported:	Two 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB drives

CONNECTIONS
Function	Location
40-pin IDE(AT) connector	J1
34-pin floppy drive connector	J2
16-pin game port internal	J3
9-pin serial port 1 - external	J4
10-pin serial port 2 - internal	J5
25-pin parallel port - external	J6
4-pin connector - drive active LED	JP1

USER CONFIGURABLE SETTINGS
Function		Location	Setting
»	IDE(AT) interface enabled	JP2/pins 1 & 2	closed
	IDE(AT) interface disabled	JP2/pins 2 & 3	closed
»	Floppy drive interface enabled	JP3/pins 1 & 2	closed
	Floppy drive interface disabled	JP3/pins 2 & 3	closed
»	Game port enabled	JP8/pins 1 & 2	closed
	Game port disabled	JP8/pins 2 & 3	closed
»	EPP IOCHRDY signal enabled	JP15/pins 1 & 2	closed
	EPP IOCHRDY signal disabled	JP15/pins 2 & 3	closed
»	Parallel Port IRQ 7 select	JP16/pins 1 & 2	closed
	Parallel Port IRQ 5 select	JP16/pins 2 & 3	closed
»	IDE IRQ 14 select	JP26/pins 1 & 2	closed
	IDE IRQ 10 select	JP26/pins 2 & 4	closed
	IDE IRQ 15 select	JP26/pins 2 & 3	closed
»	SIDE-2610 is primary IDE controller	JP27/pins 1 & 2	closed
	SIDE-2610 is secondary IDE controller	JP27/pins 2 & 3	closed
»	SIDE-2610 is primary floppy drive controller	JP28/pins 1 & 2	closed
	SIDE-2610 is secondary floppy drive controller	JP28/pins 2 & 3	closed

SERIAL PORT 1 CONFIGURATION
Address		JP4	JP5
»	3F8h (COM1)	pins 1 & 2 closed	pins 1 & 2 closed
	2F8h (COM2)	pins 1 & 2 closed	pins 2 & 3 closed
	3E8h (COM3)	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

SERIAL PORT 2 CONFIGURATION
Address		JP6	JP7
»	2F8h (COM2)	pins 1 & 2 closed	pins 1 & 2 closed
	3F8h (COM1)	pins 1 & 2 closed	pins 2 & 3 closed
	2E8h (COM4)	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

PARALLEL PORT ADDRESS SELECTION
Address		JP9	JP10
»	278h	pins 1 & 2 closed	pins 1 & 2 closed
	378h	pins 1 & 2 closed	pins 2 & 3 closed
	3BCh	pins 2 & 3 closed	pins 1 & 2 closed
	Disabled	pins 2 & 3 closed	pins 2 & 3 closed

PARALLEL PORT MODE SELECTION
Mode		JP11	JP12
»	ECP & EPP	pins 1 & 2 closed	pins 1 & 2 closed
	ECP	pins 2 & 3 closed	pins 1 & 2 closed
	EPP	pins 1 & 2 closed	pins 2 & 3 closed
	SPP Printer	pins 2 & 3 closed	pins 2 & 3 closed

PARALLEL PORT ECP DMA SELECTION
DMA		JP13	JP14
»	DMA1	pins 1 & 2 closed	pins 1 & 2 closed
	DMA3	pins 2 & 3 closed	pins 2 & 3 closed
	Disabled	open	open

SERIAL PORT 1 INTERRUPT SELECTION
IRQ		JP18	JP19	JP20	JP21	JP22	JP23	JP24	JP25
»	4	open	open	open	open	open	open	2 & 3	open
	3	open	open	open	open	open	open	open	2 & 3
	5	open	open	open	open	open	2 & 3	open	open
	7	open	open	open	open	2 & 3	open	open	open
	9	open	open	open	2 & 3	open	open	open	open
	10	open	open	2 & 3	open	open	open	open	open
	11	open	2 & 3	open	open	open	open	open	open
	12	2 & 3	open	open	open	open	open	open	open
Note: Designated pins are in the closed position.

SERIAL PORT 2 INTERRUPT SELECTION
IRQ		JP18	JP19	JP20	JP21	JP22	JP23	JP24	JP25
»	3	open	open	open	open	open	open	open	1 & 2
	4	open	open	open	open	open	open	1 & 2	open
	5	open	open	open	open	open	1 & 2	open	open
	7	open	open	open	open	1 & 2	open	open	open
	9	open	open	open	1 & 2	open	open	open	open
	10	open	open	1 & 2	open	open	open	open	open
	11	open	1 & 2	open	open	open	open	open	open
	12	1 & 2	open	open	open	open	open	open	open
Note: Designated pins are in the closed position.