...because we can't all be on the bleeding edge...





ADP111V

SILICON VALLEY COMPUTER INC.

ADP111V

Data bus:

32-bit, VL-bus

Size:

Full-length, full-height card

Hard drive supported:

(2) IDE(AT) interface drives, (2) IDE mirror drives, IDE tape drive

Floppy drives supported:

360KB, 720KB, 1.2MB, or 1.44MB drives

CONNECTIONS

Function

Location

9-pin serial port 1 - internal

COM1

9-pin serial port 2 - external

COM2

15-pin connector - game port

GAME1

4-pin connector - Mirror drive active LED

J1

4-pin connector - primary drive active LED

J2

40-pin connector - IDE mirror drive cable

J3

40-pin IDE(AT) interface connector

J4

40-pin ISA IDE tape/IDE CD-ROM interface connector

P1

34-pin control cable connector - floppy drive

P2

4-pin connector - IDE tape/IDE CD-ROM drive active LED

P3

25-pin parallel port - external

P4

USER CONFIGURABLE SETTINGS

Function

Location

Setting

 

8051/8031 micro controller is installed

E1

pins 1 & 2, 3 & 4 closed

 

80C51/80C31 micro controller is installed

E1

pins 2 & 3 closed

Serial port 2 enabled

E3

pins 2 & 3 closed

 

Serial port 2 disabled

E3

pins 1 & 2 closed

Parallel port enabled

E4

pins 2 & 3 closed

 

Parallel port disabled

E4

pins 1 & 2 closed

USER CONFIGURABLE SETTINGS(CONTINUED)

Function

Location

Setting

ISA IDE interface enabled

E5

pins 2 & 3 closed

 

ISA IDE interface disabled

E5

pins 1 & 2 closed

Floppy drive interface enabled

E6

pins 2 & 3 closed

 

Floppy drive interface disabled

E6

pins 1 & 2 closed

Serial port 2 address 2F8 - 2EFh select

E7

pins 2 & 3 closed

 

Serial port 2 address 2E8 - 2EFh select

E7

pins 1 & 2 closed

Serial port 1 address 3F8 - 3FFh select

E8

pins 2 & 3 closed

 

Serial port 1 address 3E8 - 3EFh select

E8

pins 1 & 2 closed

Serial port 1 enabled

E9

pins 2 & 3 closed

 

Serial port 1 disabled

E9

pins 1 & 2 closed

Parallel port address 378 - 37Fh select

E10

pins 2 & 3 closed

 

Parallel port address 278 - 27Fh select

E10

pins 1 & 2 closed

Game port enabled

E11 & E12

closed

 

Game port disabled

E11 & E12

open

ISA IDE tape drive interrupt IRQ15 select

E13

pins 2 & 3 closed

 

ISA IDE tape drive interrupt IRQ10 select

E13

pins 1 & 2 closed

 

ISA IDE tape drive interrupt IRQ14 select(do not use)

E13

pins 4 & 5 closed

VESA IDE interface interrupt IRQ14 select

E13

pins 5 & 6 closed

 

VESA IDE interface interrupt IRQ15 select(do not use)

E13

pins 6 & 7 closed

 

Factory configured - do not alter

S1/4

N/A

 

Factory configured - do not alter

S1/5

N/A

External BIOS enabled

S1/6

off

 

Internal BIOS enabled

S1/6

on

Factory configured - do not alter

S1/7

N/A

Factory configured - do not alter

S1/8

N/A

Factory configured - do not alter

SW1/4

on

BASE MEMORY ADDRESS SELECT

Address

S1/1

S1/2

CC000h

on

off

 

D8000h

off

on

 

DC000h

off

off

 

Disabled

on

on

BIOS SIZE

Size

E2

S1/3

8KB

open

on

 

16KB

closed

off

Note: The manufacturer recommends that the default value of 8KB should not be changed by the user.

DATA TRANSFER RATE TABLE

 

CPU Speed/Type

Setting

25/DX2-50 MHz

33/DX-66 MHz

50MHz

0

1.67

2.22

3.33

1

2.00

2.66

4.00

2

2.50

3.33

5.00

3

2.94

3.92

5.88

4

3.12

4.60

6.25

5

4.16

5.55

8.33

6

4.54

6.06

9.09

7

6.25

8.33

12.50

DATA TRANSFER RATE SWITCH SETTINGS

Setting

SW1/1

SW1/2

SW1/3

0

on

on

on

1

on

on

off

2

on

off

on

3

on

off

off

4

off

on

on

5

off

on

off

6

off

off

on

7

off

off

off