...because we can't all be on the bleeding edge...





5500MF

AMERICAN DATA AQUISITION CORPORATION

5500MF

Card Type

Data Aquisition

Chip Set

Unidentified

Maximum Onboard Memory

Unidentified

I/O Options

Analog input, digital input

Hard Drives supported

None

Floppy drives supported

None

Data Bus

8-bit ISA

Card Size

Half length

CONNECTIONS

Function

Label

Function

Label

37-pin analog/digital signals connector

J1

Bipolar offset selector

P2

A/D converter gain selector

P1

Unipolar offset selector

P3

USER CONFIGURABLE SETTINGS

Function

Label

Position

1.02 MHz PIT clock 1 input

JP8

Pins 1 & 2 closed

 

External PIT clock 1 input

JP8

Pins 2 & 3 closed

Factory configured - do not alter

JP11

Open

A/D channel not sequenced

JP12

Open

 

A/D channel auto sequenced

JP12

Closed

DIGITAL INPUT/OUTPUT SELECTION

Setting

Label

Position

Digital I/O inputs (0-3)

JP4

Open

 

Digital I/O outputs (0-3)

JP4

Closed

Digital I/O inputs (4-7)

JP5

Open

 

Digital I/O outputs (4-7)

JP5

Closed

Digital I/O outputs (8-11)

JP6

Closed

 

Digital I/O inputs (8-11)

JP6

Open

Digital I/O outputs (12-15)

JP7

Closed

 

Digital I/O inputs (12-15)

JP7

Open

A/D TRIGGER SOURCE SELECTION

Source

JP1

Software trigger only

Open

External trigger

Pins 1 & 2 closed

PIT counter 0 trigger

Pins 2 & 3 closed

A/D RANGE SELECTION

Polarity

Voltage

JP2

JP3

JP9

JP10

Bipolar

+ 10V

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

 

Bipolar

+ 5V

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

 

Unipolar

0-10V

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Note: Pins designated are in the closed position

BASE I/O ADDRESS SELECTION

Setting

W9

W8

W7

W6

W5

W4

 

000h

Closed

Closed

Closed

Closed

Closed

Closed

 

010h

Closed

Closed

Closed

Closed

Closed

Open

 

020h

Closed

Closed

Closed

Closed

Open

Closed

 

030h

Closed

Closed

Closed

Closed

Open

Open

 

040h

Closed

Closed

Closed

Open

Closed

Closed

200h

Open

Closed

Closed

Closed

Closed

Closed

 

3B0h

Open

Open

Open

Closed

Open

Open

 

3C0h

Open

Open

Open

Open

Closed

Closed

 

3D0h

Open

Open

Open

Open

Closed

Open

 

3E0h

Open

Open

Open

Open

Open

Closed

 

3F0h

Open

Open

Open

Open

Open

Open

Note:

A total of 256 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. W9 is the Most Significant Bit and switch W4 is the Least Significant Bit. The switches have the following decimal values: W9=512, W8=256, W7=128, W6=64, W5=32, W4=16. Turn off the switches and add the values of the switches to obtain the correct memory address. (Close=0, Open=1)