...because we can't all be on the bleeding edge...
NATIONAL INSTRUMENTS
AT-MIO-16F-5
|
Card Type |
Analog to digital timing converter |
|
Chipset Controller |
Unidentified |
|
I/O Options |
Analog input, analog output, digital input, digital output |
|
Maximum DRAM |
N/A |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
34-pin interface connector |
J1 |
50-pin I/O connector |
J2 |
|
BASE I/O ADDRESS SELECTION | ||||||
|
Address |
U67/A5 |
U67/A6 |
U67/A7 |
U67/A8 |
U67/A9 | |
| » |
220h |
Off |
On |
On |
On |
Off |
|
000h |
On |
On |
On |
On |
On | |
|
020h |
Off |
On |
On |
On |
On | |
|
040h |
On |
Off |
On |
On |
On | |
|
060h |
Off |
Off |
On |
On |
On | |
|
080h |
On |
On |
Off |
On |
On | |
|
360h |
Off |
Off |
On |
Off |
Off | |
|
380h |
On |
On |
Off |
Off |
Off | |
|
3A0h |
Off |
On |
Off |
Off |
Off | |
|
3C0h |
On |
Off |
Off |
Off |
Off | |
|
3E0h |
Off |
Off |
Off |
Off |
Off | |
|
Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. Switch A9 is the Most Significant Bit and switch A5 is the Least Significant Bit. The switches have the following decimal values: switch A9=512, A8=256, A7=128, A6=64, A5=32. Turn off the switches and add the values of the switches that are off to obtain the correct memory address. (Off=1, On=0) | ||||||
|
DMA CHANNEL SELECTION (DMA A) | |||||||
|
DMA |
W4/A |
W4/B |
W4/C |
W4/D |
W4/E |
W4/F | |
| » |
6 |
Open |
Open |
Pins 1 & 2 |
Pins 1 & 2 |
Open |
Open |
|
0 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
1 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
2 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
5 |
Pins 1& 2 |
Pins 1& 2 |
Open |
Open |
Open |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Pins 1 & 2 |
Pins 1 & 2 | |
|
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | |||||||
|
DMA CHANNEL SELECTION (DMA A CON’T) | |||||||||
|
DMA |
W7/A |
W7/B |
W7/C |
W7/D |
W7/E |
W7/F |
W7/G |
W7/H | |
| » |
6 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
0 |
1 & 2 |
1 & 2 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
1 |
Open |
Open |
1 & 2 |
1 & 2 |
Open |
Open |
Open |
Open | |
|
2 |
Open |
Open |
Open |
Open |
1 & 2 |
1 & 2 |
Open |
Open | |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open |
1 & 2 |
1 & 2 | |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Disabled |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | |||||||||
|
DMA CHANNEL SELECTION (DMA B) | |||||||
|
DMA |
W4/A |
W4/B |
W4/C |
W4/D |
W4/E |
W4/F | |
| » |
7 |
Open |
Open |
Open |
Open |
Pins 2 & 3 |
Pins 2 & 3 |
|
0 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
1 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
2 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
5 |
Pins 2 & 3 |
Pins 2 & 3 |
Open |
Open |
Open |
Open | |
|
6 |
Open |
Open |
Pins 2 & 3 |
Pins 2 & 3 |
Open |
Open | |
|
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | |||||||
|
DMA CHANNEL SELECTION (DMA B CON’T) | |||||||||
|
DMA |
W7/A |
W7/B |
W7/C |
W7/D |
W7/E |
W7/F |
W7/G |
W7/H | |
| » |
7 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
0 |
2 & 3 |
2 & 3 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
1 |
Open |
Open |
2 & 3 |
2 & 3 |
Open |
Open |
Open |
Open | |
|
2 |
Open |
Open |
Open |
Open |
2 & 3 |
2 & 3 |
Open |
Open | |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open |
2 & 3 |
2 & 3 | |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
6 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Disabled |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | |||||||||
|
INTERRUPT SELECTION | |||||||
|
IRQ |
W5/A |
W5/B |
W5/C |
W5/D |
W5/E |
W5/F | |
| » |
10 |
Open |
Open |
Open |
Open |
Closed |
Open |
|
2/9 |
Open |
Open |
Open |
Open |
Open |
Closed | |
|
3 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
4 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
6 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Open |
Open | |
|
11 |
Open |
Open |
Open |
Closed |
Open |
Open | |
|
12 |
Open |
Open |
Closed |
Open |
Open |
Open | |
|
14 |
Open |
Closed |
Open |
Open |
Open |
Open | |
|
15 |
Closed |
Open |
Open |
Open |
Open |
Open | |
|
Disabled |
Open |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | |||||||
|
INTERRUPT SELECTION (CON’T) | ||||||
|
IRQ |
W6/A |
W6/B |
W6/C |
W6/D |
W6/E | |
| » |
10 |
Open |
Open |
Open |
Open |
Open |
|
2/9 |
Open |
Open |
Open |
Open |
Open | |
|
3 |
Pins 1 & 2 |
Open |
Open |
Open |
Open | |
|
4 |
Open |
Pins 1 & 2 |
Open |
Open |
Open | |
|
5 |
Open |
Open |
Pins 1 & 2 |
Open |
Open | |
|
6 |
Open |
Open |
Open |
Pins 1 & 2 |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Pins 1 & 2 | |
|
11 |
Open |
Open |
Open |
Open |
Open | |
|
12 |
Open |
Open |
Open |
Open |
Open | |
|
14 |
Open |
Open |
Open |
Open |
Open | |
|
15 |
Open |
Open |
Open |
Open |
Open | |
|
Disabled |
Open |
Open |
Open |
Open |
Open | |
|
Note: Pins designated are in the closed position. | ||||||
|
ANALOG OUTPUT CONFIGURATION | |||
|
Type |
W8 (Channel 1) |
W11 (Channel 0) | |
| » |
Internal |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
External |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
|
ANALOG OUTPUT POLARITY CONFIGURATION | |||
|
Type |
W9 (Channel 1) |
W10 (Channel 0) | |
| » |
Bipolar |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
Unipolar |
Pins 1 & 2 closed |
Pins 1 & 2 closed | |
|
Note: Use this table in conjunction with the table below to set jumpers for Bipolar & Unipolar mode selection. | |||
|
BIPOLAR & UNIPOLAR OUTPUT MODE CONFIGURATION | |||
|
Mode |
W12 (Channel 1) |
W13 (Channel 0) | |
| » |
Two’s Complement |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
Straight Binary |
Pins 2 & 3 closed |
Pins 2 & 3 closed | |
|
Note: Bipolar can use both modes, while Unipolar uses the straight binary mode only. | |||
|
RTSI BUS CLOCK CONFIGURATION | |||
|
Setting |
W1 |
W2 | |
| » |
Use local oscillator board signal |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
Receive the RTSI bus signal |
Pins 1 & 2 closed |
Pins 1 & 2 closed | |
|
Drive RTSI bus & board/OSC |
Pins 1 & 2 closed |
Pins 2 & 3 closed | |