EVERGREEN SYSTEMS, INC.
CAPSERVER MODELS 325E, 425, 440E
|
Processor |
AM386SX/CX486SLC/80386SX/TI486SXLC2 |
|
Processor Speed |
25/40MHz |
|
Chip Set |
Unidentified |
|
Max. Onboard DRAM |
16MB |
|
Cache |
None |
|
BIOS |
Unidentified |
|
Dimensions |
Unidentified |
|
I/O Options |
10-baseT Ethernet connector, floppy drive interface, IDE interface, parallel port, proprietary display connector, serial ports (2), thin Ethernet connector, VGA port |
|
NPU Options |
80387SX |
|
CONNECTIONS | |||
|
Purpose |
Location |
Purpose |
Location |
|
Thin Ethernet connector |
BNC |
Speaker |
J12 |
|
Proprietary display/CAPlink |
DISP |
External battery |
J13 |
|
Floppy drive interface |
FLP |
Parallel port |
PAR |
|
IDE interface |
IDE |
Serial port 1 (10-pin modular) |
SER1 |
|
Keylock |
J6 |
Serial port 2 |
SER2 |
|
Alternate keyboard |
J7 |
Ethernet 10BaseT connector |
TBT |
|
Reset switch |
J11 |
VGA port |
VGA |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Jumper |
Position | |
|
» |
Onboard VGA controller enabled |
W1 |
Closed |
|
Onboard VGA controller disabled |
W1 |
Open | |
|
» |
VGA IRQ9 disabled |
W2 |
Open |
|
VGA IRQ9 enabled |
W2 |
Closed | |
|
» |
Ethernet select 10BaseT |
W3 |
pins 1 & 2 closed |
|
Ethernet select thin |
W3 |
pins 2 & 3 closed | |
|
» |
AT bus disabled (Capcard only receives DC from backplane) |
W4 |
Open |
|
AT bus enabled (Capcard may drive peripheral cards) |
W4 |
Closed | |
|
» |
IDE interrupt select edge triggered |
W5 |
pins 1 & 2 closed |
|
IDE interrupt select level triggered |
W5 |
pins 2 & 3 closed | |
|
» |
Floppy drive IRQ6 enabled |
W6 |
Closed |
|
|
Floppy drive IRQ6 disabled |
W6 |
Open |
|
Note: Only one card in a segment can have W4 closed. Damage will result otherwise. See Below. | |||
|
DRAM CONFIGURATION TABLE | ||
|
Size |
Bank 0 |
Bank 1 |
|
2MB |
(2) 1M x 9 |
NONE |
|
4MB |
(2) 1M x 9 |
(2) 1M x 9 |
|
10MB |
(2) 1M x 9 |
(2) 4M x 9 |
|
16MB |
(2) 4M x 9 |
(2) 4M x 9 |
|
CAPCARD ID CONFIGURATION | |||||
|
ID# |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
|
1 |
Off |
Off |
Off |
Off |
On |
|
2 |
Off |
Off |
Off |
On |
Off |
|
3 |
Off |
Off |
Off |
On |
On |
|
4 |
Off |
Off |
On |
Off |
Off |
|
5 |
Off |
Off |
On |
Off |
On |
|
6 |
Off |
Off |
On |
On |
Off |
|
7 |
Off |
Off |
On |
On |
On |
|
8 |
Off |
On |
Off |
Off |
Off |
|
9 |
Off |
On |
Off |
Off |
On |
|
10 |
Off |
On |
Off |
On |
Off |
|
11 |
Off |
On |
Off |
On |
On |
|
12 |
Off |
On |
On |
Off |
Off |
|
13 |
Off |
On |
On |
Off |
On |
|
14 |
Off |
On |
On |
On |
Off |
|
15 |
Off |
On |
On |
On |
On |
|
16 |
On |
Off |
Off |
Off |
Off |
|
17 |
On |
Off |
Off |
Off |
On |
|
18 |
On |
Off |
Off |
On |
Off |
|
19 |
On |
Off |
Off |
On |
On |
|
20 |
On |
Off |
On |
Off |
Off |
|
21 |
On |
Off |
On |
Off |
On |
|
22 |
On |
Off |
On |
On |
Off |
|
23 |
On |
Off |
On |
On |
On |
|
CAPCARD ID CONFIGURATION | |||||
|
ID# |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
|
24 |
On |
On |
Off |
Off |
Off |
|
25 |
On |
On |
Off |
Off |
On |
|
26 |
On |
On |
Off |
On |
Off |
|
27 |
On |
On |
Off |
On |
On |
|
28 |
On |
On |
On |
Off |
Off |
|
29 |
On |
On |
On |
Off |
On |
|
30 |
On |
On |
On |
On |
Off |
|
Note: Capcard ID’s are necessary for the card to distinguish between cards. #1 is considered the server. | |||||
|
RESTORING FACTORY DEFAULTS | |||
|
Setting |
SW1/6 |
SW1/7 |
SW1/8 |
|
Normal operation |
Off |
Off |
Off |
|
Restore defaults boot from 1.44MB A: |
On |
Off |
Off |
|
Restore defaults boot from 40MB C: |
Off |
On |
Off |
|
Restore defaults boot from Novell network |
Off |
Off |
On |
|
Suppress EEPROM overide and use CMOS |
Off |
On |
On |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Jumper |
Position | |
|
» |
Interprocessor Communications Unit enabled |
W7/IPCU DIS |
Open |
|
Interprocessor Communications Unit disabled |
W7/IPCU DIS |
Closed | |
|
» |
Onboard drive controllers enabled |
W7/FDCIDE DIS |
Open |
|
Onboard drive controllers disabled |
W7/FDCIDE DIS |
Closed | |
|
» |
Factory configured - do not alter |
W7/SCC SEL2 |
Open |
|
» |
Factory configured - do not alter |
W7/SCC SEL1 |
Open |
|
» |
Factory configured - do not alter |
W8/ all |
Open |
|
» |
Factory configured - do not alter |
W9/ all |
Open |
|
» |
Factory configured - do not alter |
W14/ all |
Open |
|
PRIMARY SERIAL PORT CONFIGURATION | ||
|
Port address |
W7/COM1 SEL1 |
W7/COM1 SEL2 |
|
COM1 |
Open |
Open |
|
COM2 |
Closed |
Open |
|
COM3 |
Open |
Closed |
|
Disabled |
Closed |
Closed |
|
SECONDARY SERIAL PORT CONFIGURATION | ||
|
Port address |
W7/COM2 SEL1 |
W7/COM2 SEL2 |
|
COM1 |
Open |
Open |
|
COM2 |
Closed |
Open |
|
COM3 |
Open |
Closed |
|
Disabled |
Closed |
Closed |
|
PARALLEL PORT CONFIGURATION | ||
|
Port address |
W7/PAR SEL1 |
W7/PAR DIS |
|
LPT1 |
Open |
Open |
|
LPT2 |
Closed |
Open |
|
Disabled |
Open |
Closed |
|
ENET ADDRESS CONFIGURATION | |||
|
Address |
W7/ENET SEL1 |
W7/ENET SEL2 |
W7/ENET DIS |
|
300h |
Open |
Open |
Open |
|
320h |
Closed |
Open |
Open |
|
340h |
Open |
Closed |
Open |
|
360h |
Closed |
Closed |
Open |
|
Disabled |
Open |
Open |
Closed |
|
ENET INTERRUPT CONFIGURATION | ||||
|
Interrupt |
W10/IRQ3 |
W10/IRQ4 |
W10/IRQ5 |
W10/IRQ9 |
|
IRQ3 |
Closed |
Open |
Open |
Open |
|
IRQ4 |
Open |
Closed |
Open |
Open |
|
IRQ5 |
Open |
Open |
Closed |
Open |
|
IRQ9 |
Open |
Open |
Open |
Closed |
|
PARALLEL PORT INTERRUPT CONFIGURATION | ||
|
Interrupt |
W11/IRQ5 |
W11/IRQ7 |
|
IRQ5 |
Closed |
Open |
|
IRQ7 |
Open |
Closed |
|
Disabled |
Open |
Open |
|
SERIAL PORT INTERRUPT CONFIGURATION | ||
|
Port |
W12/IRQ3 |
W12/ IRQ4 |
|
COM1 |
pins COM1 & IRQ3 closed |
pins COM1 & IRQ4 closed |
|
COM2 |
pins COM2 & IRQ3 closed |
pins COM2 & IRQ3 closed |
|
Note: Names represent pins in diagram. The diagram shows COM1 at IRQ4 and COM2 at IRQ3. | ||
|
IPCU INTERRUPT CONFIGURATION | ||||
|
Interrupt |
W13/IRQ7 |
W13/IRQ11 |
W13/IRQ12 |
W13/IRQ15 |
|
IRQ7 |
Closed |
Open |
Open |
Open |
|
IRQ11 |
Open |
Closed |
Open |
Open |
|
IRQ12 |
Open |
Open |
Closed |
Open |
|
IRQ15 |
Open |
Open |
Open |
Closed |
|
WARNING |
|
ONLY ONE CARD IN A GIVEN SEGMENT OF THE ABOVE BACKPLANES MAY HAVE ITS AT BUS JUMPER INSTALLED AT W4. IF MORE THEN ONE CARD HAS W4 INSTALLED DAMAGE WILL OCCUR. |
|
TERMINATING RESISTOR CONFIGURATION | |
|
Setting |
R100 |
|
First and last CAPcards in CAPserver |
Installed |
|
All other cards in CAPserver |
Not installed |