Processor	Pentium
Processor Speed	60MHz
Chip Set	Unidentified
Video Chip Set	None
Maximum Onboard Memory	192MB
Maximum Video Memory	None
Cache	256/512KB
BIOS	Unidentified
Dimensions	355mm x 304mm
I/O Options	32-bit PCI slots (3), floppy drive interface, IDE interface, parallel port, PS/2 mouse port, serial ports (2)
NPU Options	None

CONNECTIONS
Purpose	Location	Purpose	Location
Speaker	J11	IDE interface	J22
PS/2 mouse port	J15	Auxiliary power	P3
Parallel port	J18	Power LED	W9
Floppy drive interface	J19	IDE interface LED	W10
Serial port 1	J20	32-bit PCI slots	PC1 – PC3
Serial port 2	J21

USER CONFIGURABLE SETTINGS
Function		Label	Position
»	Parity check enabled	J1	Closed
	Parity check disabled	J1	Open
»	Cache type select write back	J2	Open
	Cache type select write through	J2	Closed
»	Oscillator for U15	J6	Pins 1 & 2 closed
	Clock synthesizer	J6	Pins 2 & 3 closed
»	BIOS normal operation	W2	Pins 2 & 3 closed
	BIOS recovery mode	W2	Pins 1 & 2 closed
»	PS/2 mouse enabled	W6	Closed
	PS/2 mouse disabled	W6	Open
»	Factory configured - do not alter	W20	Pins 2 & 3 closed

SIMM CONFIGURATION
Size	Bank 0	Bank 1	Bank 2
8MB	(2) 1M x 36	None	None
16MB	(2) 1M x 36	(2) 1M x 36	None
16MB	(2) 2M x 36	None	None
24MB	(2) 1M x 36	(2) 1M x 36	(2) 1M x 36
32MB	(2) 2M x 36	(2) 2M x 36	None
32MB	(2) 4M x 36	None	None
48MB	(2) 2M x 36	(2) 2M x 36	(2) 2M x 36
64MB	(2) 4M x 36	(2) 4M x 36	None
64MB	(2) 8M x 36	None	None
96MB	(2) 4M x 36	(2) 4M x 36	(2) 4M x 36
128MB	(2) 8M x 36	(2) 8M x 36	None
128MB	(2) 16M x 36	None	None
192MB	(2) 8M x 36	(2) 8M x 36	(2) 8M x 36

CACHE CONFIGURATION

Note: The location of the cache is unidentified.

CACHE JUMPER CONFIGURATION
Size	J3	J4	J35
None	Pins 1 & 2 closed	Pins 1 & 2 closed	Open
256KB	Pins 2 & 3 closed	Pins 1 & 2 closed	Pins 1 & 2 closed
512KB	Pins 2 & 3 closed	Pins 2 & 3 closed	Pins 2 & 3 closed

CPU CLOCK SPEED SELECTION
Speed	J5
50MHz	Closed
66MHz	Open

CPU VOLTAGE SELECTION
Voltage	J40	J41	J42
5v	Closed	N/A	N/A
5.3v	Power module installed	Power module installed	Power module installed
Note: All pins on J40 must be closed.

DMA CHANNEL SELECTION
Channel	W14	W16
6	Pins 1 & 2 closed	Pins 1 & 2 closed
7	Pins 2 & 3 closed	Pins 2 & 3 closed