...because we can't all be on the bleeding edge...
COMPEX, INC.
ANET16-1A (REV. B)
|
NIC Type |
ARCnet |
|
Transfer Rate |
2.5Mbps |
|
Data Bus |
16-bit ISA |
|
Topology |
Star Linear Bus |
|
Wiring Type |
Unshielded twisted pair RG-62A/U 93ohm coaxial |
|
Boot ROM |
Available |
|
NODE ADDRESS | ||||||||
|
Node |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
0 |
- |
- |
- |
- |
- |
- |
- |
- |
|
1 |
Off |
On |
On |
On |
On |
On |
On |
On |
|
2 |
On |
Off |
On |
On |
On |
On |
On |
On |
|
3 |
Off |
Off |
On |
On |
On |
On |
On |
On |
|
4 |
On |
On |
Off |
On |
On |
On |
On |
On |
|
251 |
Off |
Off |
On |
Off |
Off |
Off |
Off |
Off |
|
252 |
On |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
253 |
Off |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
254 |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
255 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
Note:Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1) | ||||||||
|
INTERRUPT REQUEST | ||||||||||
|
IRQ |
JP1A |
JP1B |
JP1C |
JP1D |
JP1E |
JP1F |
JP1G |
JP1H |
JP1I | |
| » |
2/9 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
3 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open | |
|
4 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open | |
|
5 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open | |
|
7 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed | |
|
10 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open | |
|
11 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open | |
|
12 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
15 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open | |
|
I/O BASE ADDRESS | ||||
|
Address |
JP2A |
JP2B |
JP2C | |
|
260h |
Closed |
Closed |
Closed | |
|
290h |
Open |
Closed |
Closed | |
| » |
2E0h |
Closed |
Open |
Closed |
|
2F0h |
Open |
Open |
Closed | |
|
300h |
Closed |
Closed |
Open | |
|
350h |
Open |
Closed |
Open | |
|
380h |
Closed |
Open |
Open | |
|
3E0h |
Open |
Open |
Open | |
|
BOOT ROM ADDRESS | |||||||
|
Address |
JP3A |
JP3B |
JP3C |
JP3D |
JP3E | ||
|
C0000h 1 |
Closed |
Closed |
Closed |
Closed |
Closed | ||
|
C4000h 1 |
Closed |
Closed |
Open |
Closed |
Closed | ||
|
CC000h |
Closed |
Closed |
Closed |
Open |
Closed | ||
| » |
D0000h |
Closed |
Closed |
Open |
Open |
Closed | |
|
D4000h |
Closed |
Closed |
Closed |
Closed |
Open | ||
|
D8000h |
Closed |
Closed |
Open |
Closed |
Open | ||
|
DC000h |
Closed |
Closed |
Closed |
Open |
Open | ||
|
E0000h |
Closed |
Closed |
Open |
Open |
Open | ||
|
Note 1 :These options can be supported by XT or fully XT-compatible PCs only. | |||||||
|
WAIT STATE | ||
|
Setting |
JP4 | |
| » |
Zero wait states disabled |
Open |
|
Zero wait states enabled |
Closed | |
|
Note:If Zero wait state is enabled, IOCHRDY (JP5) must be disabled. | ||
|
I/O CHANNEL READY | ||
|
Setting |
JP5 | |
| » |
IOCHRDY signal disabled |
Open |
|
IOCHRDY signal enabled |
Closed | |
|
Note:If IOCHRDY signal is enabled, Zero wait state (JP4) must be disabled. If optional PROM is installed, IOCHRDY must be enabled and Zero wait state (JP4) must be disabled. | ||
|
CABLE TYPE | ||
|
Type |
JP7 & JP8 | |
| » |
RG62A/U 93ohm coaxial |
Pins 1 & 2 Closed |
|
Unshielded twisted pair |
Pins 2 & 3 Closed | |
|
TOPOLOGY CONFIGURATION | ||
|
Mode |
JP9 | |
| » |
Star |
Closed |
|
Linear Bus |
Open | |
|
DIAGNOSTIC LED(S)S | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Red |
On |
Network connection is good |
|
LED1 |
Red |
Blinking |
Network connection is bad or no other nodes are active |
|
LED2 |
Green |
On |
Data is being transmitted or received |
|
LED2 |
Green |
Off |
Data is not being transmitted or received |
|
LED2 |
Green |
Blinking |
System is being powered up |