...because we can't all be on the bleeding edge...





PRONET-10 P1308

PROTEON, INC.

PRONET-10 P1308

NIC Type

Token Ring

Transfer Rate

4/16Mbps

Data Bus

16-bit ISA

Topology

Star

Wiring Type

Unshielded twisted pair

AUI transceiver via DB-15 port

Boot ROM

Available

NODE ADDRESS

Node

SW1/1

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

SW1/7

SW1/8

0

-

-

-

-

-

-

-

-

1

Off

On

On

On

On

On

On

On

2

On

Off

On

On

On

On

On

On

3

Off

Off

On

On

On

On

On

On

4

On

On

Off

On

On

On

On

On

251

Off

Off

On

Off

Off

Off

Off

Off

252

On

On

Off

Off

Off

Off

Off

Off

253

Off

On

Off

Off

Off

Off

Off

Off

254

On

Off

Off

Off

Off

Off

Off

Off

255

Off

Off

Off

Off

Off

Off

Off

Off

Note:Node address 0 is used for messaging between nodes and must not be used.

A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

16-BIT DMA CHANNEL

Channel

JP1

JP15

DMA5

Pins 3 & 4 and 5 & 6 closed

Pins 2 & 3 closed

 

DMA6

Pins 3 & 4 and 2 & 7 closed

Pins 2 & 4 closed

 

DMA7

Pins 3 & 4 and 1 & 8 closed

Pins 1 & 2 closed

 

Disabled

Open

Open

Note:For use in an AT-class machine only.

8-BIT DMA CHANNEL

Channel

JP7

JP18

DMA1

Pins 3 & 4 and 2 & 7 closed

Pins 1 & 2 closed

 

DMA2

Pins 3 & 4 and 1 & 8 closed

Pins 2 & 3 closed

 

DMA3

Pins 3 & 4 and 5 & 6 closed

Pins 2 & 4 closed

 

Disabled

Open

Open

Note:Can be used in either a PC/XT-class machine or an AT-class machine.

INTERRUPT REQUEST

IRQ

JP22

2

Pins 2 & 6 closed

 

3

Pins 5 & 9 closed

 

4

Pins 4 & 8 closed

 

5

Pins 3 & 7 closed

 

10

Pins 9 & 13 closed

 

11

Pins 8 & 12 closed

 

12

Pins 7 & 11 closed

 

14

Pins 1 & 6 closed

 

15

Pins 6 & 10 closed

COMPATIBILITY MODE

Setting

JP32

JP36

Compatibility mode enabled

Pins 1 & 2 closed

Pins 1 & 2 closed

 

Extended mode enabled

Pins 2 & 3 closed

Pins 2 & 3 closed

Note:Extended mode provides 16-bit data transfers and hardware checksums in an AT-class machine when the card is installed in a 16-bit slot. When the card is installed in an 8-bit slot, extended mode only provides hardware checksums.

BOOT ROM

Setting

JP38

Disabled

Open

 

Enabled

Closed

CABLE TYPE

Type

JP40

JP42

JP44

JP46

Unshielded twisted pair

Closed

Closed

Closed

Closed

AUI transceiver via DB-15 port

Open

Open

Open

Open

BOOT ROM ADDRESS

Address

SW2/1

SW2/2

SW2/3

SW2/4

 

C0000h

On

On

On

On

 

C4000h

On

On

On

Off

 

C8000h

On

On

Off

On

 

CC000h

On

On

Off

Off

 

D0000h

On

Off

On

On

 

D4000h

On

Off

On

Off

D8000h

On

Off

Off

On

 

DC000h

On

Off

Off

Off

 

E0000h

Off

On

On

On

 

E4000h

Off

On

On

Off

 

E8000h

Off

On

Off

On

 

EC000h

Off

On

Off

Off

 

F0000h

Off

Off

On

On

 

F4000h

Off

Off

On

Off

 

F8000h

Off

Off

Off

On

 

FC000h

Off

Off

Off

Off

I/O BASE ADDRESS

Address

SW2/5

SW2/6

SW2/7

SW2/8

300h 1

On

On

On

On

308h

On

On

On

Off

310h 1

On

On

Off

On

318h

On

On

Off

Off

320h 1

On

Off

On

On

328h

On

Off

On

Off

330h 1

On

Off

Off

On

338h

On

Off

Off

Off

340h 1

Off

On

On

On

348h

Off

On

On

Off

350h 1

Off

On

Off

On

358h

Off

On

Off

Off

360h 1

Off

Off

On

On

368h

Off

Off

On

Off

370h 1

Off

Off

Off

Off

378h

Off

Off

Off

Off

Note: Use any of the above settings when compatibility mode (JP32 & JP36) is enabled.

Note 1 :Use only these settings when extended mode (JP32 & JP36) is enabled.