...because we can't all be on the bleeding edge...





CTD2004H-S, CTD4004H-S, CTD8004H-S, CTD2004R-S, CTD4004R-S, CTD8004R-S

CONNER PERIPHERALS, INC.

CTD2004H-S, CTD4004H-S, CTD8004H-S, CTD2004R-S, CTD4004R-S, CTD8004R-S

Device Type

Internal Tape Drive

Interface

SCSI-2

Format

DDS (CTD2004H-S and CTD2004R-S)

DDS-DC (CTD4004H-S and CTD4004R-S)

DDS-2 (CTD8004H-S and CTD8004R-S)

Sustained Transfer Rate

550KBPS

1,100KBPS (compressed - CTD4004H-S, CTD8004H-S, CTD4004R-S, and CTD8004R-S only)

Size

3.5 in. half height (CTD2004H-S, CTD4004H-S, and CTD8004H-S)

5.25 in. half height (CTD2004R-S, CTD4004R-S, and CTD8004R-S with adapter)

View

Bottom

USER CONFIGURABLE SETTINGS

Setting

Label

Position

»

Factory configured - do not alter

JP1/Pins 7-10

Unidentified

»

Termination enabled

JP1/Pins 11 & 12

Closed

 

Termination disabled

JP1/Pins 11 & 12

Open

»

Factory configured - do not alter

JP1/Pins 13 & 14

Unidentified

»

MRS Mode disabled

SW1/S4

On

 

MRS Mode enabled

SW1/S4

Off

»

Parity check disabled

SW1/S5

Off

 

Parity check enabled

SW1/S5

On

»

Data compression enabled

SW1/S6

Off

 

Data compression disabled

SW1/S6

On

»

Factory configured - do not alter

SW1/S7

Off

»

Self-Test disabled

SW1/S8

Off

 

Self-Test enabled

SW1/S8

On

Note: MRS (Media Recognition System) Mode enabled allows drive to detect DDS cartridges that support this feature.

DRIVE SELECT ID

Drive ID

JP1/Pins 1 & 2

JP1/Pins 3 & 4

JP1/Pins 5 & 6

»

0

Open

Open

Open

 

1

Closed

Open

Open

 

2

Open

Closed

Open

 

3

Closed

Closed

Open

 

4

Open

Open

Closed

 

5

Closed

Open

Closed

 

6

Open

Closed

Closed

 

7

Closed

Closed

Closed

Note: If using Pins 1-6 of JP1 for SCSI ID selection, S1, S2, and S3 of SW1 must be set to the ‘Off’ position.

DRIVE SELECT ID

Drive ID

SW1/S1

SW1/S2

SW1/S3

»

0

Off

Off

Off

 

1

On

Off

Off

 

2

Off

On

Off

 

3

On

On

Off

 

4

Off

Off

On

 

5

On

Off

On

 

6

Off

On

On

 

7

On

On

On

Note: If using S1, S2, and S3 of SW1 for SCSI ID selection, Pins 1-6 of JP1 must be set to the ‘Open’ position.

TERMINATION POWER SELECTION

Setting

JP1/Pins 15 & 16

»

TERMPWR supplied by drive

Closed

 

TERMPWR supplied by SCSI interface to drive

Open

MANUFACTURERS RECOMMENDED MEDIA

Drive

Tape

Capacity Without Compression

Capacity With Compression

CTD2004H-S

90 meter DDS DAT cartridge

2.0GB

N/A

CTD2004R-S

90 meter DDS DAT cartridge

2.0GB

N/A

CTD4004H-S

90 meter DDS-DC DAT cartridge

2.0GB

4.0GB

CTD4004R-S

90 meter DDS-DC DAT cartridge

2.0GB

4.0GB

CTD8004H-S

90 meter DDS-DC DAT cartridge

2.0GB

4.0GB

CTD8004H-S

120 meter DDS-2 DAT cartridge

4.0GB

8.0GB

CTD8004R-S

90 meter DDS-DC DAT cartridge

2.0GB

4.0GB

CTD8004R-S

120 meter DDS-2 DAT cartridge

4.0GB

8.0GB

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

LED1

Green

On

Cartridge is inserted and does not generate excessive errors

LED1

Green

Slow Flash

Cartridge is inserted but generates excessive errors (cleaning may be required)

LED1

Green

Fast Flash

Drive could not write to tape correctly - cleaning required

LED1

Green

Off

Cartridge not inserted

LED2

Yellow

On

Drive is reading or writing the tape

LED2

Yellow

Fast Flash

Hardware fault occurred

LED2

Yellow

Off

Drive not busy

Note: If LED1 flashes during Slow Flash of LED2, a prerecorded audio cartridge is inserted and is being played automatically. Use DDS DAT cleaning cartridges only.