...because we can't all be on the bleeding edge...
TANDBERG DATA
TDC 3500, TDC 3700
|
Device Type |
Tape Drive |
|
Interface |
SCSI-2 |
|
Format |
QIC-3040 (read only for TDC-3700) QIC-3210 |
|
Sustained Transfer Rate |
300KBPS |
|
Size |
3.5 in. half height |
|
View |
Top |
|
CONNECTIONS | |
|
Function |
Label |
|
Ground connector |
CN1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
| » |
Factory configured - do not alter. (BIRDOUT Test) |
JP1/Pins 1 & 2 |
Unidentified |
| » |
Factory configured - do not alter. (BIRDIN Test) |
JP1/Pins 3 & 4 |
Unidentified |
|
Parity enabled |
JP1/Pins 11 & 12 |
Closed | |
|
Parity disabled |
JP1/Pins 11 & 12 |
Open | |
|
Termination enabled |
JP1/Pins 21 & 22 |
Closed | |
|
Termination disabled |
JP1/Pins 21 & 22 |
Open | |
|
DRIVE SELECT ID | |||
|
Drive ID |
JP1/Pins 13 & 14 |
JP1/Pins 15 & 16 |
JP1/Pins 17 & 18 |
|
0 |
Open |
Open |
Open |
|
1 |
Open |
Open |
Closed |
|
2 |
Open |
Closed |
Open |
|
3 |
Open |
Closed |
Closed |
|
4 |
Closed |
Open |
Open |
|
5 |
Closed |
Open |
Closed |
|
6 |
Closed |
Closed |
Open |
|
7 |
Closed |
Closed |
Closed |
|
Note: Pins 2 & 4 must be open to enable SCSI select. | |||
|
TERMINATION POWER SELECTION | ||
|
Setting |
JP1/Pins 19 & 20 | |
| » |
TERMPWR supplied by drive |
Closed |
|
TERMPWR supplied by SCSI interface to drive |
Open | |
|
MANUFACTURERS RECOMMENED MEDIA | |||
|
Drive |
Tape |
Capacity Without Compression |
Capacity With Compression |
|
TDC 3500 |
3M® MC3000 295ft.
|
640MB |
Unidentified |
|
TDC 3500 |
3M® MC3000XL 400ft. |
840MB |
Unidentified |
|
TDC 3500 |
SONY® QW3000XL 400ft. |
1.0GB |
Unidentified |
|
TDC 3700 |
SONY® QW3000MP++ 425ft. |
2.3GB |
Unidentified |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Green |
Blink 1 |
Cleaning operation in progress |
|
LED1 |
N/A |
Off |
Cleaning operation completed |
|
LED1 |
Amber |
Blink 1 |
DPCC 2 has completed all cleanings and is out of filament |
|
Note: A Dry Process Cleaning Cartridge (TDS DPCC-2000) is required to enable the above cleaning functions. 1 LED will blink at two cycles per second. 2 Dry Process Cleaning Cartridge. 1) If eject button is pressed during cleaning operations, LED will blink green at six cycles per second. The DPCC will be automatically ejected when the cleaning process is completed, cleaning operations will not be interrupted by the eject command, and the LED will turn off when the eject sequence is completed. 2) If eject button is pressed before cleaning operations, LED will blink green at six cycles per second, and the DPCC will be ejected immediately. If drive is already performing a DPCC insert sequence, it will be completed before the cartridge is ejected. 3) If eject button is pressed after cleaning operations are completed, LED will blink green at six cycles per second, and the cartridge will be ejected immediately. | |||