Card Type	Fax, Modem (synchronous/asynchronous)
Chip Set	U.S. Robotics
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	External
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.25bis, V.32, V.32bis, V.34 Rockwell V.FC U.S. Robotics HST, V.32terbo
Fax Modulation Protocol	ITU-T V.17, V.21, V.27ter, V.29
Error Correction/Compression	HST, MNP5, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
RS-232/422		CN1		DC power		CN4
Line out		CN2		Voice/Data switch		SW2
Line in		CN3		Power switch		SW3

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í DTR normal	SW1/A	Off
DTR forced high	SW1/A	On
í Verbose (word) format enabled	SW1/B	Off
Numeric format enabled	SW1/B	On
í Result code display enabled	SW1/C	On
Result code display disabled	SW1/C	Off
í Local echo enabled	SW1/D	Off
Local echo disabled	SW1/D	On
í Auto-answer disabled	SW1/E	On
Auto-answer enabled, off-hook on first ring	SW1/E	Off
í CD normal	SW1/F	Off
CD forced high	SW1/F	On
í Result code display enabled in both originate and answer mode	SW1/G	Off
Result code display enabled in originate mode only	SW1/G	On
í Smart mode	SW1/H	On
Dumb mode	SW1/H	Off
í Escape code response: modem goes on-hook, off-line command mode, returns ‘NO CARRIER’	SW1/I	Off
Escape code response: modem stays on-line, on-line command mode, returns ‘OK’	SW1/I	On
í Reset and load from profiles in NVRAM	SW1/J	Off
Reset and load from factory settings in ROM	SW1/J	On

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
HS	Red	On	Modem is operating at 2400bps or faster
HS	Red	Off	Modem is operating at slower than 2400bps
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
AA	Red	Blinking	Phone is ringing
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
MR	Red	On	Power is on
MR	Red	Off	Power is off
RS	Red	On	Modem sends RTS signal
RS	Red	Off	RTS forced low during receive data hardware flow control
CS	Red	On	Synchronous transmission or before CTS forced low during transmit hardware flow control
CS	Red	Off	Modem doesn’t send CTS to remote
SYN	Red	On	Modem in synchronous mode
SYN	Red	Off	Modem not in synchronous mode
SYN	Red	Blinking	Dial security enabled
ARQ/FAX	Red	On	Modem is connected in ARQ mode
ARQ/FAX	Red	Off	Modem is not connected in ARQ mode
ARQ/FAX	Red	Slow blink	Data being retransmitted
ARQ/FAX	Red	Fast blink	Modem is connected in FAX mode