...because we can't all be on the bleeding edge...





PCMCIA 14400BPS DATA/14400BPS FAX

ANGIA COMMUNICATIONS, INC.

PCMCIA 14400BPS DATA/14400BPS FAX

Card Type

Fax, Modem (asynchronous)

Chip Set

Unidentified

Maximum Data Rate

14.4Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA Type II

Fax Class

Class I

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

V2329

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘Comma’, A/

A, B, C, D, E, F, H, L, M, O, P, Q, S, T, V, W, X, Y, Z

&C, &D, &E, &G, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \K, \N \Q, \V, \X, \Z, %A, %E

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S11, S12, S16, S18, S25, S26, S36

S38, S39, S46, S48

Note: See MHI Help file for full command documentation.

Proprietary AT Command Set

BIT MAPPED REGISTERS

Register

Default

S14

Read-only

S19

26

S20

32

S21

Read-only

S22

Read-only

S23

Read-only

S27

Read-only

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

Data compression disabled

%C1

Data compression enabled; V.42bis during LAPM, MNP5 during MNP

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Direct mode enabled

\N1

Normal mode enabled

\N2

MNP reliable mode enabled

\N3

MNP auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

V.42 auto-reliable mode enabled

\N6

Reliable mode enabled

í \N7

Auto-reliable mode enabled

DISPLAY FIRMWARE VERSION

Type:

Immediate

Format:

AT [cmds] %V [cmds]

Description:

Displays firmware version information

ENQ/ACK

Type:

Configuration

Format:

AT [cmds] \Hn [cmds]

Description:

Controls Hewlett Packard ENQ/ACK protocol

Command

Function

í \H0

Hewlett Packard ENQ/ACK disabled

\H1

Hewlett Packard ENQ/ACK emulating terminal enabled

\H2

Hewlett Packard ENQ/ACK emulating host

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

&F0

Restore auto-reliable compression/correction default profile

&F1

Restore auto-reliable compression/correction default profile

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Default:

0

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects.

MINIMUM MODEM PORT RATE

Type:

Configuration

Format:

AT [cmds] %Mn [cmds]

Description:

Selects the minimum modem port rate

Command

Function

í %M300

300bps selected

%M1200

1200bps selected

%M2400

2400bps selected

%M4800

4800bps selected

%M7200

7200bps selected

%M9600

9600bps selected

%M12000

12000bps selected

%M14400

14400bps selected

MODEM PORT RATE

Type:

Configuration

Format:

AT [cmds] %Bn [cmds]

Description:

Selects the modem port rate

Command

Function

%B300

300bps selected

%B1200

1200bps selected

%B2400

2400bps selected

%B4800

4800bps selected

%B7200

7200bps selected

%B9600

9600bps selected

%B12000

12000bps selected

í %B14400

14400bps selected

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Reports ‘OK’

I3

Reports a date code