|
APACHE V34I-M
APACHE MICRO PERIPHERALS, INC.
APACHE V34I-M
|
Card Type
|
Modem (asynchronous)
|
|
Chip Set
|
Rockwell ACi
|
|
I/O Options
|
None
|
|
Maximum Data Rate
|
28.8Kbps
|
|
Maximum Fax Rate
|
14.4Kbps
|
|
Data Bus
|
Unidentified
|
|
Fax Class
|
Unidentified
|
|
Data Modulation Protocol
|
Bell 103A/212A
ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34
Rockwell V.FC
|
|
Fax Modulation Protocol
|
Unidentified
|
|
Error Correction/Compression
|
MNP5, V.42, V.42bis
|
52998
|
USER CONFIGURABLE SETTINGS
|
|
Setting
|
Label
|
Position
|
|
í Factory configured - do not alter
|
SW1/7
|
Unidentified
|
|
í Factory configured - do not alter
|
SW1/8
|
N/A
|
|
Note: SW1/8 may not be present on all models.
|
|
INTERRUPT SELECTION
|
|
Setting
|
SW1/1
|
SW1/2
|
SW1/3
|
SW1/4
|
|
í IRQ3
|
Off
|
Off
|
Off
|
On
|
|
IRQ4
|
Off
|
Off
|
On
|
Off
|
|
IRQ5
|
Off
|
On
|
Off
|
Off
|
|
IRQ7
|
On
|
Off
|
Off
|
Off
|
|
SERIAL PORT ADDRESS SELECTION
|
|
Setting
|
SW1/5
|
SW1/6
|
|
3F8h (COM1:)
|
On
|
On
|
|
2F8h (COM2:)
|
Off
|
On
|
|
3E8h (COM3:)
|
On
|
Off
|
|
í 2E8h (COM4:)
|
Off
|
Off
|
|
MISCELLANEOUS TECHNICAL NOTE
|
|
Diagram not available.
|
|
SUPPORTED STANDARD COMMANDS
|
|
Basic AT Commands
|
|
+++, ‘comma’, A/
|
|
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z
|
|
&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z
|
|
Extended AT Commands
|
|
\A, \B, \K, \N
|
|
%C, %E, %L, %Q
|
|
Special AT Commands
|
|
#CID, +MS
|
|
S-Registers
|
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26
|
|
S27, S29, S30, S31, S32, S33, S36, S38, S46, S48, S82, S86, S95
|
|
Note: See MHI documentation for complete information.
Registers S39, S40, and S41 are unidentified bit-mapped registers.
|
Proprietary AT Command Set
|
DIAL
|
|
Type:
|
Immediate
|
|
Format:
|
AT [cmds] D<#>;[cmds]
|
|
Description:
|
Dials the telephone number indicated according to any modifiers included in the string.
|
|
Note:
|
Any combination of modifiers can be used to produce the desired dial functions in sequence.
|
|
Command
|
Function
|
|
DL
|
Re-dial last number.
|
|
DP
|
Pulse dialing enabled.
|
|
DS=n
|
Dial stored telephone number n.
|
|
DT
|
Tone dialing enabled.
|
|
DW
|
Dialing resumed following dial tone detection.
|
|
D,
|
Dialing paused for amount of time specified in S8 register.
|
|
D!
|
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
|
|
D@
|
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
|
|
D$
|
Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command.
|
|
D^
|
Enables calling tone for this call.
|
|
D;
|
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.
|
|
LINE SPEED
|
|
Type:
|
Register
|
|
Format
|
AT [cmds] S37=n [cmds]
|
|
Description:
|
Sets the maximum allowable data exchange rate attempted during handshake process.
|
|
Command
|
Function
|
|
í S37=0
|
Speed of last connection.
|
|
S37=1
|
Maximum speed set to 300bps.
|
|
S37=2
|
Maximum speed set to 300bps.
|
|
S37=3
|
Maximum speed set to 300bps.
|
|
S37=5
|
Maximum speed set to 1200bps.
|
|
S37=6
|
Maximum speed set to 2400bps.
|
|
S37=7
|
Maximum speed set to 1200/75bps.
|
|
S37=8
|
Maximum speed set to 4800bps.
|
|
S37=9
|
Maximum speed set to 9600bps.
|
|
S37=10
|
Maximum speed set to 12Kbps.
|
|
S37=11
|
Maximum speed set to 14.4Kbps.
|
|
S37=12
|
Maximum speed set to 7200bps.
|
|
REPORT INFORMATION
|
|
Type:
|
Immediate
|
|
Format:
|
AT [cmds] In [cmds]
|
|
Description:
|
Displays requested information about the modem.
|
|
Command
|
Function
|
|
I0
|
Reports product identification code.
|
|
I1
|
Reports ROM checksum.
|
|
I2
|
Tests and reports ROM checksum.
|
|
I3
|
Reports modem firmware version and interface type.
|
|
I6
|
Reports data pump model and revision.
|
|