BEST DATA PRODUCTS, INC.
SMART ONE 2834F, SMART ONE 2834V, SMART ONE 2834VP
|
Card Type |
Modem (asynchronous) |
|
Chipset |
Unidentified |
|
I/O Options |
Voice (except on Smart One 2834F) |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class I & II |
|
Data Modulation |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10EC, V.42, V.42bis |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Line out |
CN1 |
Line in |
CN2 |
|
INTERRUPT SELECTION | ||||
|
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
|
í IRQ3 |
On |
Off |
Off |
Off |
|
IRQ4 |
Off |
On |
Off |
Off |
|
IRQ5 |
Off |
Off |
On |
Off |
|
IRQ7 |
Off |
Off |
Off |
On |
|
SERIAL PORT ADDRESS SELECTION | ||
|
Setting |
SW1/5 |
SW1/6 |
|
3F8h (COM1:) |
On |
On |
|
í 2F8h (COM2:) |
On |
Off |
|
3E8h (COM3:) |
Off |
On |
|
2E8h (COM4:) |
Off |
Off |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, ‘comma’, A/ |
|
A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \G, \K, \N |
|
%C, %E, %L, %Q |
|
Special AT Commands |
|
#CID, +MS |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26 |
|
S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 |
Note: See MHI documentation for complete information. |
|
UNIDENTIFIED COMMANDS | |
|
Command |
Default |
|
S37 |
0 |
|
S201 |
Unidentified |
Proprietary AT Command Set
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays ROM checksum. |
|
I3 |
Displays firmware model, revision, and interface. |
|
I5 |
Displays country code. |
|
I6 |
Displays data pump model and revision. |
|
I7 |
Displays the DAA code. |
|
MNP10 POWER LEVEL ADJUSTMENT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] )Mn [cmds] |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation. |
|
Command |
Function |
|
)M0 |
Power level adjustment disabled. |
|
)M1 |
Power level adjustment enabled. |
|
)M2 |
Power level adjustment enabled; S40 bit 2 and S201 bit 6 are reset to their default settings. |
|
MNP10EC MODE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] -SEC=n [cmds] | |
|
Description: |
Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. | |
|
Command |
Function | |
|
-SEC=0 |
MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. | |
|
í -SEC=1 |
MNP10EC handshaking enabled. | |