...because we can't all be on the bleeding edge...





MAGIC MP56

ACER, INC.

MAGIC MP56

Card Type

Modem (asynchronous), Fax, Sound card

Chip Set

Unidentified

I/O Options

CD-ROM interface, game port, wavetable interface, audio line in, audio line out, microphone

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34

Fax Modulation Protocol

ITU-T V.17, V.33, V.29, V.27ter, V.21CH2

Error Correction/Compression

MNP 5, V.42bis

Fax Class

Unidentified

Data Bus

16-bit ISA

CONNECTIONS

Function

Label

Function

Label

Line out

CN1

Wavetable interface

CN6

Line in

CN2

CD-ROM connector

CN7

Microphone

CN3

MIDI/Game port

CN8

Audio line in

CN4

Ring-on connector

CN9

Speaker/audio line-out

CN5

   

USER CONFIGURABLE SETTINGS

Setting

Label

Position

Flash download disabled

JP4

Pins 1 & 2 closed

Flash download enabled

JP4

Pins 2 & 3 closed

 

 

 

 

 

 

 

 

 

 

 

 

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &F, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z

Extended AT Commands

\K, \N

%E, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S95

Special Commands

+MS

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

N1

Auto-mode detection enabled

CLOCK SOURCE - SYNCHRONOUS TRANSMIT

Type:

Configuration

Format:

AT [cmds] &Xn [cmds]

Description:

Selects DTE transmit clock source

Command

Function

&X0

Modem generates clock

&X1

DTE generates clock

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR acts per V.25

 

 

 

 

 

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

&Q Setting

&D0

&D1

&D2

&D3

&Q0, &Q5, &Q6

Command 0

Command 1

Command 2

Command 3

&Q1, &Q4

Command 2

Command 1

Command 2

Command 3

&Q2, &Q3

Command 2

Command 2

Command 2

Command 2

Command

Function

Command 0

Modem does not respond to DTR

Command 1

Modem goes to command mode after DTR goes is off

Command 2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

Command 3

Modem is initialized after DTR goes off

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Disable DTE/DCE flow control

&K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

&K6

Unidirectional XON/XOFF flow control enabled

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Note: Used primarily for international data transmission

Command

Function

&G0

Guard tone disabled

&G1

Guard tone disabled

&G2

1800Hz guard tone enabled

 

 

 

 

 

 

 

 

 

 

 

 

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem model and speed

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Report firmware revision, model and interface type

I4

Report response programmed by OEM

I5

Report the country code parameter

I6

Report modem data pump model and code revision

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting

TRANSMIT CARRIER

Type:

Configuration

Format:

AT [cmds] Cn [cmds]

Description:

Controls the transmit carrier switching

S(status) -REGISTERS

AUTO SYNCHRONIZATION OPTION

Format

AT [cmds] S19=n [cmds]

Default:

0

Range:

Unidentified

Unit:

Unidentified

Description:

Options are unidentified

BIT-MAPPED REGISTER S20

Format

AT [cmds] S20=n [cmds]

Default:

0,

Range:

0-253

Unit:

Bit-mapped

Description:

Selects auto-sync HDLC address or BSC sync character