...because we can't all be on the bleeding edge...





TR114+I8V-T1

BROOKTROUT TECHNOLOGY, INC.

TR114+I8V-T1

Card Type

ISDN

NIC Type

ISDN

Maximum Onboard Memory

2MB

Network Transfer Rate

1.544Mbps

Topology

Star

Wiring Type

Unshielded twisted pair

Data Bus

16-bit ISA

CONNECTIONS

Function

Label

Function

Label

RJ-45 UTP connector

CN1

MVIP connector

CN2

USER CONFIGURABLE SETTINGS

Function

Label

Position

Card is first and only card in system

SW3/1

On

Card is not first in a multiple card system

SW3/1

Off

T1 loopback test disabled

SW5

Off

T1 loopback test enabled

SW5

On

BASE I/O ADDRESS SELECTION

Setting

SW3/2

SW3/3

SW3/4

SW3/5

SW3/6

SW3/7

SW3/8

100h

On

On

On

On

On

Off

On

108h

On

On

On

Off

On

Off

On

110h

On

On

On

On

Off

Off

On

118h

On

On

On

On

On

On

Off

120h

On

On

Off

On

On

On

Off

260h

On

On

Off

Off

On

On

Off

3D8h

Off

Off

Off

Off

On

On

Off

3E0h

Off

Off

Off

Off

Off

On

On

3E8h

Off

Off

Off

Off

Off

On

Off

3F0h

Off

Off

Off

Off

Off

Off

On

3F8h

Off

Off

Off

Off

Off

Off

Off

Note:

A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW1/8 is the Most Significant Bit and switch SW1/1 is the Least Significant Bit. The switches have the following decimal values: SW1/8=32768, SW1/7=16384, SW1/6=8192, SW1/5=4096, SW1/4=2048, SW1/3=1024, SW1/2=512, SW1/1=256. Turn off the switches and add the values of the switches to obtain the correct memory address. (Off=1, On=0)

INTERRUPT SELECTION

IRQ

JP1

3

Pins 1 & 2 closed

4

Pins 3 & 4 closed

5

Pins 5 & 6 closed

6

Pins 7 & 8 closed

7

Pins 9 & 10 closed

9

Pins 11 & 12 closed

10

Pins 13 & 14 closed

11

Pins 15 & 16 closed

12

Pins 17 & 18 closed

14

Pins 19 & 20 closed

15

Pins 21 & 22 closed

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

LED1

Red

Blinking

Data is being transmitted on channel 0

LED1

Red

Blinking (fast)

Channel 0 is off hook

LED2

Red

Blinking

Data is being transmitted on channel 1

LED2

Red

Blinking (fast)

Channel 1 is off hook

LED3

Red

Blinking

Data is being transmitted on channel 2

LED3

Red

Blinking (fast)

Channel 2 is off hook

LED4

Red

Blinking

Data is being transmitted on channel 3

LED4

Red

Blinking (fast)

Channel 3 is off hook

LED5

Red

Blinking

Data is being transmitted on channel 4

LED5

Red

Blinking (fast)

Channel 4 is off hook

LED6

Red

Blinking

Data is being transmitted on channel 5

LED6

Red

Blinking (fast)

Channel 5 is off hook

LED7

Red

Blinking

Data is being transmitted on channel 6

LED7

Red

Blinking (fast)

Channel 6 is off hook

LED8

Red

Blinking

Data is being transmitted on channel 7

LED8

Red

Blinking (fast)

Channel 7 is off hook

D1

Red

On

TR114+I8V-T1 in network loopback mode

D2

Red

On

Loss of T1 network signal

D3

Yellow

On

Failing to synchronize on incoming T1 signal

D2 & D3

Red/Yellow

Both on

Board cannot detect a valid T1 signal

D4

Green

On

Operating in normal mode

FRM

Unidentified

On

T1 framing error detected

BPV

Unidentified

On

T1 bipolar violation detected

CRC

Unidentified

On

Discrepancy in cyclic redundancy check detected

MVIP CLOCK TERMINATION

Setting

SW4/1

SW4/2

Terminated

On

On

Not terminated

Off

Off

USER CONFIGURABLE SETTINGS

Function

Label

Position

T1 generates and transmits the clocking signals to the TR114

SW1/1

Off

TR114 generates and transmits the clocking signals to T1

SW1/1

On

Super frame mode

SW1/2

Off

Extended super frame mode

SW1/2

On

B8ZS line coding

SW1/3

Off

AMI line coding

SW1/3

On

MVIP clock master set to master

SW2/3

Off

MVIP clock master set to slave

SW2/3

On

T1 CABLE LENGTH SETTTINGS

Cable Length

SW1/4

SW1/5

SW1/6

0 to 132 ft.

On

On

On

133 to 266 ft.

Off

On

On

267 to 398 ft.

On

Off

On

399 to 532 ft.

Off

Off

On

533 to 654 ft.

On

On

Off

MVIP STREAM SELECT

Mode

SW2/1

SW2/2

6/7

Off

Off

4/5

On

Off

2/3

Off

On

0/1

On

On

SYNC SOURCE CONTROL

Setting

SW2/3

SW2/4

TR114+I8V-T1 controls

Off

Off

Secondary net card controls

Off

On

FRAMING SIGNAL OUTPUT

Setting

SW2/3

SW2/4

Disable output

On

Off

Enable output

On

On

TERMINATION

Setting

SW2/5

SW2/6

Unterminated

Off

Off

Terminated

On

On