...because we can't all be on the bleeding edge...





9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1)

CARDINAL TECHNOLOGIES, INC

9600BPS V.32 V.42BIS FAX (1/2CARD-VER.1)

Card Type

Modem (asynchronous)

Chip Set

Unidentified

Maximum Data Rate

9600bps

Maximum Fax Rate

Unidentified

Data Bus

8-bit ISA

Fax Class

Class I & II

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.32

Fax Modulation Protocol

Unidentified

Error Correction/Compression

MNP5, V.42, V.42bis

CONNECTIONS

Function

Label

Function

Label

Line out/in

CN1

Line in/out

CN2

SERIAL PORT ADDRESS

Setting

SW1/1

SW1/2

COM1 (3F8h)

Off

Off

COM2 (2F8h)

Off

On

COM3 (3E8h)

On

Off

COM4 (2E8h)

On

On

INTERRUPT SELECTION

Setting

SW1/3

SW1/4

2

On

On

3

Off

On

4

Off

Off

5

On

Off

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘Comma’, A/

A, B, C, E, F, H, L, M, N, O, P, Q, S, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \O, \U, \V, \X, \Y, \Z

%A, %E, %G

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S25

S26, S27, S30, S37, S95, S108, S109, S110

Special Commands

"H, "O, -C, -J, -V

Note: Please see MHI Help file for full command documentation.

Proprietary AT Command Set

BIT-MAPPED REGISTER S23

Format

AT [cmds] S23=n [cmds]

Default:

15

Range:

0-191

Unit:

Bit-mapped

Description:

Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.

Bit

Value

Function

0

0

í 1

Remote digital loopback denied

Remote digital loopback allowed

3 - 1

000

001

010

011

100

101

110

í 111

Sets serial port speed to 0-300bps

Sets serial port speed to 1200bps

Sets serial port speed to 2400bps

Sets serial port speed to 4800bps

Sets serial port speed to 7200bps

Sets serial port speed to 9600bps or 14400bps

Sets serial port speed to 19200bps

Sets serial port speed to 38400bps or 57600bps

5, 4

í 00

01

10

11

Parity even

Space or No parity

Parity odd

Mark Parity

7, 6

í 00

01

10

Guard tone disabled

Guard tone 550Hz enabled

Guard tone 1800Hz enabled

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal

Command

Break from DTE in RELIABLE or NORMAL mode

Modem receives \B during command state

Break from DTE in DIRECT mode

Break received from remote modem

\K0

Online command mode enabled, send no break to remote modem

Break sent to remote modem and buffers cleared

Online command mode enabled, send break to remote modem

Buffers cleared, break sent to DTE

\K1

Break sent to remote modem and buffers cleared

Break sent to remote modem and buffers cleared

Send break to remote modem immediately

Buffers cleared, break sent to DTE

\K2

Online command mode enabled, send no break to remote modem

Send break to remote modem immediately

Online command mode enabled, send break to remote modem

Break sent immediately to DTE

\K3

Send break to remote modem immediately

Send break to remote modem immediately

Send break to remote modem immediately

Break sent immediately to DTE

\K4

Online command mode enabled, send no break to remote modem

Send break with transmitted data

Online command mode enabled, send break to remote modem

Break sent with received data to the DTE

í \K5

Send break with transmitted data

Send break with transmitted data

Send break to remote modem immediately

Break sent with received data to the DTE

COMPRESSION

Type:

Configuration

Format:

AT [cmds] %Cn [cmds]

Description:

Selects data compression

Command

Function

%C0

MNP5 disabled

í %C1

MNP5 enabled

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

MNP reliable mode enabled

í \N3

V.42 auto-reliable mode enabled

\N4

V.42 reliable mode enabled

\N5

LAPM/Normal mode enabled

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Modifier

Function

P

Pulse dialing enabled

R

Answer mode enabled, originate mode disabled following handshake initiation

S=n

Dial stored telephone number n=0-3

T

Tone dialing enabled

W

Dialing resumed following dial tone detection

,

Dialing paused for amount of time specified in S8 register

!

Modem commanded to go off-hook for specified time before returning on-hook

@

Wait for quiet answer

;

Modem returned to command state after dialing

DTE CONNECT SPEED

Type:

Configuration

Format:

AT [cmds] S112=n [cmds]

Description:

Select the DTE speed during data transfer

Command

Function

í S112=0

Last AT speed

S112=1

Not used

S112=2

Sets DTE speed to 300bps

S112=3

Sets DTE speed to 1200bps

S112=4

Sets DTE speed to 2400bps

S112=5

Sets DTE speed to 4800bps

S112=6

Sets DTE speed to 7200bps

S112=7

Sets DTE speed to 9600bps

S112=8

Sets DTE speed to 12000bps

S112=9

Sets DTE speed to 14400bps

S112=10

Sets DTE speed to 16800bps

S112=11

Sets DTE speed to 19200bps

S112=12

Sets DTE speed to 38400bps

S112=13

Sets DTE speed to 57600bps

S112=14

Sets DTE speed to 600bps

FLOW CONTROL TYPE

Type:

Configuration

Format:

AT [cmds] \Qn [cmds]

Description:

Sets type of flow control used by modem

Command

Function

\Q0

Flow control disabled

\Q1

Bi-directional XON/XOFF flow control enabled

\Q2

Unidirectional hardware flow control enabled

í \Q3

Bi-directional hardware flow control enabled (RTS/CTS)

INACTIVITY TIMER

Type:

Configuration

Format:

AT [cmds] \Tn [cmds]

Default:

0

Range:

0-90

Unit:

1 minute

Description:

Sets the length of time that the modem does not receive information before it disconnects.

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports ROM components

I4

Reports modem capabilities