...because we can't all be on the bleeding edge...





SUPRAEXPRESS 288I SP

DIAMOND MULTIMEDIA SYSTEMS, INC.

SUPRAEXPRESS 288I SP

Card Type

Modem, Fax

Chip Set

Unidentified

I/O Options

Speaker out, microphone, RJ-11 (2)

Maximum Modem Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.Fast

Fax Modulation Protocol

ITU-T V.17, V.27ter, V.29, Unidentified

Error Correction/Compression

MNP10,MNP5, V.42, V.42bis, Unidentified

Fax Class

Class I

Data Bus

16-bit ISA

Card Size

Half-length, half-height card

CONNECTIONS

Function

Label

Function

Label

Line in

CN1

Speaker out

CN3

Line out

CN2

Microphone

CN4

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

A, B, D, E, H, M, O, Q, V, W, X,

&C, &V

Extended AT Commands

%C, %G

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S25, S36, S38

Special Commands

+MS

Note: See MHI Help File for full command documentation.

 

 

 

 

 

 

Proprietary AT Command Set

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

í N1

In originate mode, handshake begins at line speed designated by the S37 register. Modem can shift to a slower speed if necessary.

In answer mode, handshake attempted with the following protocols in order - V.FC, V.32bis, V.32, V.22bis, V.22 or Bell 212, V.21, and Bell 103

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Selects communications mode options

Command

Mode

í &Q0

Asynchronous mode, serial port speed follows connect speed.

&Q5

Error correction mode

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

í &D0

Modem does not respond to DTR

&D1

Modem goes to command mode after DTR goes is off

&D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

&D3

Modem is initialized after DTR goes off

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

&F0

Direct mode, no flow control

í &F2

Reliable mode, flow control enabled

 

 

 

 

 

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

í &K3

RTS/CTS flow control enabled

&K4

XON/XOFF flow control enabled

&K5

Transparent XON/XOFF flow control enabled

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product code ID

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports ROM code revision number

I4

Reports supported protocols in encrypted format

I5

Reports firmware copyright information

I7

Reports data pump model

I10

Reports optional features supported by the modem

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

í L2

Medium volume setting

L3

Highest volume setting

Extended AT Commands

CONNECT MODE

Type:

Configuration

Format:

AT [cmds] \Nn [cmds]

Description:

Controls the type of connection the modem will operate in

Command

Function

\N0

Normal mode enabled

\N1

Direct mode enabled

\N2

Reliable mode enabled

\N3

Auto-reliable mode enabled

\N4

V.42 reliable mode enabled

 

REQUEST A RETRAIN

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls the retrain request

Command

Function

%E0

Do not request a retrain

%E1

Request a retrain

S(status) -REGISTERS

CONNECTION FAILURE CODES

Type:

Register

Format

AT [cmds] S86? [cmds]

Description:

Reports codes which correspond to the possible causes of a connection failure

Value

Meaning

0

Normal hang up

4

Carrier signal lost

5

No error-control detected for remote modem during feature negotiation

9

No common protocol found

12

No failure - remote modem disconnected normally

13

Remote modem failed to respond after 10 re-transmissions same message

14

Violation of negotiated protocol caused failure

DCE LINE SPEED

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Sets the maximum allowable data exchange rate attempted during handshake process.

Command

Function

í S37=0

Speed of last connection

S37=1

300bps

S37=5

1200bps

S37=6

2400bps

S37=8

4800bps

S37=9

9600bps

S37=10

12000bps

S37=11

14400bps

S37=12

7200bps

 

 

 

 

 

 

 

 

 

ERROR CORRECTION/COMPRESSION

Type:

Register

Format:

AT [cmds] S46=n [cmds]

Default:

136, 138

Range:

138

Description:

Selects active error correction and compression protocols

Command

Function

S46=136

Active error correction and compression protocols disabled

S46=138

Active error correction and compression protocols enabled

EXTENDED RESULT CODES

Type:

Register

Format

AT [cmds] S95=n [cmds]

Range:

0-255

Unit:

Bit-mapped

Description:

Works in combination with the Wn command to enable extended result codes. Features enabled by S95 take precedence over the options selected by Wn.

Bit

Value

Function

0

0

1

CONNECT result code reports DTE speed.

CONNECT result code reports line speed instead DTE speed.

1

0

1

Verbose CONNECT result codes display DTE or line speed only.

Adds "/ARQ" to all verbose CONNECT result codes except "NONE."

2

0

1

CARRIER result codes disabled.

CARRIER result codes enabled.

3 - 4

0

Reserved

5

0

1

COMPRESSION result codes disabled.

COMPRESSION result codes enabled.

FEATURE NEGOTIATION OPTIONS

Type:

Register

Format:

AT [cmds] S48=n [cmds]

Description:

Selects active error correction and compression protocols

Command

Function

S48=0

Detection negotiation disabled, XID negotiation disabled

í S48=7

Detection negotiation and XID negotiation enabled

S48=128

Fall-back to options set in S36