Card Type	Modem(synchronous/asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA
Fax Class	Class I & II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

BITS PER CHARACTER
Type:	Configuration
Format:	AT [cmds] $Ln [cmds]
Description:	Controls bits per character
Command		Function
$L0		8 bits per character
$L1		9 bits per character
í $L2		10 bits per character
$L3		11 bits per character

CARRIER DETECT
Type:	Configuration
Format:	AT [cmds] &Cn [cmds]
Description:	Controls DCD, Computer Systems Interface and Port Contender
Command		Function
&C0		DCD forced high
í &C1		DCD follows remote modem
&C2		Conforms to Computer Systems Interface
&C3		Conforms to Port Contender

CLEAR DOWN/DISCONNECT
Type:	Configuration
Format:	AT [cmds] Yn [cmds]
Description:	Controls long space disconnect and V.32 clear down
Command		Function
í Y0		Long space disconnect disabled
Y1		Long space disconnect enabled
Y2		V.32 clear down enabled
Y3		V.32 clear down and long space disconnect enabled

COMPRESSION
Type:	Configuration
Format:	AT [cmds] $Cn [cmds]
Description:	Controls data compression
Command		Function
$C0		Data compression disabled
í $C1		Data compression enabled

CONNECT/SPEED MESSAGE
Type:	Configuration
Format:	AT [cmds] $Xn [cmds]
Description:	Controls connect and speed message displayed
Command		Function
$X0		Normal connect and DCE speed message enabled
$X1		Normal connect and DTE speed message enabled
í $X2		Extended connect and DCE speed message enabled
$X3		Extended connect and DTE speed message enabled

DIAL INTERRUPT
Type:	Configuration
Format:	AT [cmds] $Kn [cmds]
Description:	Controls dial interrupt
Command		Function
$K0		Dial interrupt disabled
í $K1		Dial interrupt enabled

DISPLAY STORED INFORMATION
Type:	Configuration
Format:	AT [cmds] &Vn [cmds]
Description:	Displays stored phone numbers, configuration profiles and S registers
Command		Function
&V0		Display stored phone numbers
&V1		Display current configuration profiles
&V2		Display contents of S registers
&V3		Display stored profiles briefly

DSR SIGNAL
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Controls DSR, Computer Systems Interface and Port Contender
Command		Function
í &S0		DSR forced high
&S1		DSR follows remote modem
&S2		Conforms to Computer Systems Interface
&S3		Conforms to Port Contender

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] $Fn [cmds]
Description:	Controls XON/XOFF, ENQ/ACK, DTR/DSR AND CTS/RTS flow control
Command		Function
$F0		XON/XOFF enabled
$F1		XON/XOFF passthrough enabled
$F2		ENQ/ACK enabled
$F3		DTR/DSR enabled
í $F4		CTS/RTS enabled
$F5		Flow control disabled

LINE SPEED
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Controls speed at which modem attempts to connect
Command		Function
í &L0		Line speed follows DTE speed
&L1		Connect at V.23 75/1200bps
&L2		Not used
&L3		Connect at 300bps
&L4		Not used
&L5		Connect at 1200bps
&L6		Connect at 2400bps
&L7		Connect at 4800bps
&L8		Connect at 7200bps
&L9		Connect at 9600bps

PROTOCOL
Type:	Configuration
Format:	AT [cmds] $En [cmds]
Description:	Controls protocol used
Command		Function
$E0		Normal mode
$E1		Auto MNP mode
$E2		MNP mode
í $E3		Auto V.42 mode
$E4		LAPM mode

RETRAIN LIMIT
Type:	Configuration
Format:	AT [cmds] &En [cmds]
Description:	Controls number of retrains per minute allowed
Command		Function
í &E0		Disconnect If more than four retrain attempts in three minutes
&E1		Disconnect If more than four retrain attempts in four minutes
&E2		Disconnect If more than four retrain attempts in five minutes
&E3		Unlimited retrain allowed
&E4		Retrain disabled

SPEED CONVERSION
Type:	Configuration
Format:	AT [cmds] $Sn [cmds]
Description:	Controls speed conversion
Command		Function
í $S0		Speed conversion enabled
$S8		Speed conversion disabled

TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] $Tn [cmds]
Description:	Controls transmission level
Command		Function
$T0 - $T2		-4dBm
í -$T3		-6dBm
$T4		-8dBm
$T5		-10dBm
$T6		-12dBm
$T7		-14dBm
$T8		-16dBm