Card Type	Modem (asynchronous)
Chipset	Unidentified
Maximum Onboard Memory	SRAM (amount is unidentified)
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z

&C, &D, &F, &G, &P, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \V, \X, \Y, \Z

%A, %C, %E, %G, %Q

Special AT Commands

-C, -J, "H, "O

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26, S30, S90, S108, S109

Note: See MHI documentation for complete information.

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE Reliable/Normal mode		Break from DTE Direct mode	Modem receives \B	Break from remote modem
\K0	Enter command mode, do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K1	Buffers cleared and break sent to remote modem.		Send break to remote modem immediately.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K2	Enter command mode, do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Send break to remote modem immediately.	Send break to DTE immediately.
\K3	Send break to remote modem immediately.		Send break to remote modem immediately.	Send break to remote modem immediately.	Send break to DTE immediately.
\K4	Enter command mode, do not send break to remote modem.		Send break to remote modem immediately, then enter command mode.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.
\K5	Send break with transmitted data.		Send break to remote modem immediately.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Tests and displays ROM checksum.
I3	Displays device set name.
I4	Displays modem configuration.

SRAM BUFFER
Type:	Configuration
Format:	AT [cmds] Kn [cmds]
Description:	Selects whether the modem will use its internal SRAM to buffer data.
Command		Function
K0		SRAM buffer disabled.
í K1		SRAM buffer enabled.

TRELLIS CODING
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Selects whether the modem will use trellis coding.
Command		Function
í &U0		Trellis coding enabled.
&U1		Trellis coding disabled.