...because we can't all be on the bleeding edge...





TELEPATH MODEM FOR WINDOWS WITH X2

GATEWAY 2000

TELEPATH MODEM FOR WINDOWS WITH X2

Card Type

Modem

Chip Set

Unidentified

I/O Options

Soundcard connector, serial ports (2 RJ-11)

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103A/212A, ITU-T V.21, V.22, V.22bis,V.32, V.32bis, V.34, V.FC

Fax Modulation Protocol

V.17, V.21, CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

8-bit ISA

Card Size

Half-length

CONNECTIONS

Function

Label

Function

Label

Cable connector to sound card

CN1

RJ-11 telephone out

CN3

RJ-11 telephone in

CN2

   

MISCELLANEOUS TECHNICAL NOTES

A compatible sound card is necessary in order for the Speakerphone functions to operate properly.

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘comma’, A/

A, B, E, F, H, M, O, P, R, T, V, X

&C, &G,&P, &T,&X, &Z

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S38

 

Special Commands

#CID

Note: See MHI Help File for full command documentation.

VOICE COMMAND SET (DSVD)

QUEUEING DELAY

Type:

Configuration

Format:

AT [cmds] -SAD=n [cmds]

Values:

1,2,3,4

Description:

Selects max queuing delay of audio samples.

INPUT SOURCE

Type:

Configuration

Format:

AT [cmds] -SAT=n [cmds]

Description:

Selects input source.

Command

Function

SAT=0

Selects handset

SAT=1

Selects speaker-microphone

HANDSET MICROPHONE GAIN

Type:

Configuration

Format:

AT [cmds] -SHG=n [cmds]

Description:

Selects handset microphone gain.

Command

Function

SHG=0

Low gain

SHG=2

High gain

HANDSET VOLUME

Type:

Configuration

Format:

AT [cmds] -SHV=n [cmds]

Description:

Selects handset volume.

Command

Function

SHV=0

Low gain

SHV=3

High gain

MCROPHONE JACK GAIN

Type:

Configuration

Format:

AT [cmds] -SMG=n [cmds]

Description:

Selects handset microphone gain.

Command

Function

SMG=0

Low gain

SMG=2

High gain

MUTE INTERNAL SPEAKER

Type:

Configuration

Format:

AT [cmds] -SMUTE=n [cmds]

Description:

Enables/disables internal speaker.

Command

Function

SMUTE=0

Speaker enabled

SMUTE=1

Speaker disabled

INTERNAL SPEAKER AUDIO SOURCE

Type:

Configuration

Format:

AT [cmds] -SMUX=n [cmds]

Description:

Selects audio source for internal speaker.

Command

Function

SMUX=0

Selects data source

SMUX=1

Selects audio source

QUERY AUXILIARY PHONE HOOK STATUS

Type:

Configuration

Format:

AT [cmds] -SPH? [cmds]

Description:

Queries auxiliary phone hook status

AUDIO BLOCKING FACTOR

Type:

Configuration

Format:

AT [cmds] -SSB=n [cmds]

Description:

Selects audio blocking factor (#frames per V.42 packet).

DSVD MODE

Type:

Configuration

Format:

AT [cmds] -SSE=n [cmds]

Description:

Selects whether the modem will use DSVD mode.

Command

Function

í -SSE=0

DSVD mode disabled.

-SSE=1

DSVD mode enabled.

AUDIO SEQUENCE NUMBERS

Type:

Configuration

Format:

AT [cmds] -SSN=n [cmds]

Description:

Enables audio sequence numbers.

Command

Function

í -SSN=0

Audio sequence numbers disabled.

-SSN=1

Audio sequence numbers enabled.

SPEAKER JACK VOLUME

Type:

Configuration

Format:

AT [cmds] -SSV=n [cmds]

Description:

Selects speaker jack volume.

Command

Function

SSV=0

Low gain

SSV=3

High gain

For a full command summary, see GATEWAY 2000, TELEPATH WITH X2 TECHNOLOGY.