Card Type	Fax, Modem (synchronous/asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	External
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.22, V.22bis, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line in		CN1		DC power		CN4
Line out		CN2		Power switch		SW1
RS-232/422		CN3

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í SMART mode	JP1	Pins 2 & 3 closed
DUMB mode	JP1	Pins 1 & 2 closed

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
TST	Red	On	Normal operation
TST	Red	Flash	Modem has detected and corrected error
HS	Red	On	Modem is operating at 4800bps or faster
HS	Red	Off	Modem is operating at slower than 4800bps
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
AA	Red	Blinking	Phone is ringing
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
MR	Red	On	Power is on
MR	Red	Off	Power is off

ACCEPT MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \U [cmds]
Description:	Accept remote modem’s request for MNP reliable mode

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	0
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character; %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

AUTO-RETRAIN
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
í %E1	Auto-retrain enabled

BIT-MAPPED REGISTER S14
Format:		AT [cmds] S14=n [cmds]
Default:		Unidentified
Range:		0-255
Unit:		Bit-mapped
Description:		Controls echo, result codes and display, dumb mode, dial mode, stored profile, and answer/originate mode.
Bit	Value	Function
0	0 í 1	Command echo disabled Command echo enabled
2, 1	í 00 01 10	Result codes enabled Result codes disabled Result codes enabled in originate mode only
3	0 í 1	Display result codes in numeric format Display result codes in verbose format
4	í 0 1	Dumb mode disabled Dumb mode enabled
5	í 0 1	Tone dial enabled Pulse dial enabled
6	0 1	stored profile 0 stored profile 1
7	0 í 1	Answer mode enabled Originate mode enabled

BIT-MAPPED REGISTER S16
Type:		Register
Format:		AT [cmds] S16=n [cmds]
Default:		23
Range:		0-55
Unit:		Bit-mapped
Description:		Grants/denies remote digital loopback; controls clear down signal, auto-retrain, and extended result codes.
Bit	Value	Function
0	0 í 1	Remote digital loopback denied Remote digital loopback allowed
1	0 í 1	Disable clear down signal Enable clear down signal
2	0 í 1	Auto-retrain disabled Auto-retrain enabled
3	0	Not used
5, 4	00 í 01 10 11	Extended result codes disabled /DCE speed only Extended result codes/DCE speed enabled Extended result codes disabled /DTE speed only Extended result codes/DTE speed enabled

BIT-MAPPED REGISTER S21
Format		AT [cmds] S21=n [cmds]
Default:		Unidentified
Range:		0-255
Unit:		Bit-mapped
Description:		Selects originate-only mode, line mode, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function.
Bit	Value	Function
0	í 0 1	Disable originate-only mode Enable originate-only mode
1	í 0 1	Switched line Leased-line
2	0 1	CTS follows RTS CTS forced high
4, 3	00 01 10 11	DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR
5	0 í 1	DCD forced high DCD normal
6	í 0 1	DSR forced high DSR normal
7	í 0 1	Long space disconnect function disabled Long space disconnect function enabled

BIT-MAPPED REGISTER S22
Format		AT [cmds] S22=n [cmds]
Default:		118
Range:		0-255
Unit:		Bit-mapped
Description:		Controls speaker volume and controls, limits results codes, and pulse dial make/break ratio.
Bit	Value	Function
1, 0	00 01 í 10 11	Low level volume Low level volume Medium level volume High level volume
3, 2	00 í 01 10 11	Speaker off Speaker off on carrier Speaker always on Speaker on during handshake
6 - 4	000 100 101 110 í 111	Basic result codes only enabled Basic and connection speed result codes enabled Basic and connection speed result codes and dial-tone detection enabled All result codes except dial-tone detection enabled All result codes enabled
7	í 0 1	39/61ms at 10pps (North America) 33/67ms at 10pps (Europe)

BIT-MAPPED REGISTER S23
Format		AT [cmds] S23=n [cmds]
Default:		Unidentified
Range:		0-186
Unit:		Bit-mapped
Description:		Controls DTE rate and parity, and sets guard tone.
Bit	Value	Function
3 - 0	0000 0010 0011 0100 í 0110 1000 1001 1010 1011 1100 1101	Sets serial port speed to 300bps Sets serial port speed to 1200bps Sets serial port speed to 2400bps Sets serial port speed to 4800bps Sets serial port speed to 9600bps Sets serial port speed to 14400bps Sets serial port speed to 19200bps Sets serial port speed to 28800bps Sets serial port speed to 38400bps Sets serial port speed to 57600bps Sets serial port speed to 115200bps
5, 4	í 00 01 10 11	Parity even Space Parity Parity odd Mark or No Parity
7, 6	í 00 01 10	Guard tone disabled Guard tone 550Hz enabled Guard tone 1800Hz enabled

BIT-MAPPED REGISTER S27
Format		AT [cmds] S27=n [cmds]
Default:		Unidentified
Range:		0-235
Unit:		Bit-mapped
Description:		Selects synchronous/asynchronous mode, clock source, and sets DCE speed.
Bit	Value	Function
1, 0	í 00 01 10 11	Asynchronous mode, serial port speed follows connect speed Asynchronous off-line command mode and synchronous connect mode Synchronous connect mode Asynchronous off-line command mode on low DTR, synchronous connect mode on high DTR
3, 2	í 00 01 10	Local modem generates transmit clock source Local DTE generates transmit clock source Remote DCE/DTE generates transmit clock source
7 - 4	0000 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110	Sets DCE speed to 300bps Sets DCE speed to 1200bps Sets DCE speed to 2400bps Sets DCE speed to 4800bps Sets DCE speed to 7200bps Sets DCE speed to 9600bps Sets DCE speed to 12000bps Sets DCE speed to 14400bps Sets DCE speed to 16800bps Sets DCE speed to 19200bps Sets DCE speed to 21600bps Sets DCE speed to 24000bps Sets DCE speed to 26400bps Sets DCE speed to 28800bps

BIT-MAPPED REGISTER S28
Format		AT [cmds] S28=n [cmds]
Default:		16
Range:		0-149
Unit:		Bit-mapped
Description:		Controls power-on auto-connect, security call-back, auto-rate negotiation ,and DCE protocol.
Bit	Value	Function
0	í 0 1	Disabled power-on auto-connect Enabled power-on auto-connect
2, 1	í 00 01 10	Disabled security call-back Password security check only Enabled security call-back
3	í 0 1	Disable auto-rate negotiation Enable auto-rate negotiation
7 - 4	0000 í 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111	ITU-T mode Bell mode Auto-scan mode V.23 mode Set Connection speed to 300bps Set Connection speed to 1200bps Set Connection speed to 2400bps Set Connection speed to 4800bps Set Connection speed to 9600bps Set Connection speed to 14400bps Set Connection speed to 16800bps Set Connection speed to 19200bps Set Connection speed to 21600bps Set Connection speed to 24000bps Set Connection speed to 26400bps Set Connection speed to 28800bps

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE in Reliable/Normal mode		Break from DTE in Direct mode	Modem receives \B	Break received from remote modem
\K0	No break sent to remote modem		On-line command mode enabled, break sent to remote modem	Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K1	Break sent to remote modem immediately and clear buffered		Send break to remote modem immediately	Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K2	No break sent to remote modem		On-line command mode enabled, break sent to remote modem	Send break to remote modem immediately	Break sent immediately to DTE
\K3	Send break to remote modem immediately		Send break to remote modem immediately	Send break to remote modem immediately	Break sent immediately to DTE
\K4	No break sent to remote modem		On-line command mode enabled, break sent to remote modem	Send break with transmitted data	Break sent with received data to the DTE
í \K5	Send break with transmitted data		Send break to remote modem immediately	Send break with transmitted data	Break sent with received data to the DTE

CLEAR DOWN SIGNAL
Type:	Configuration
Format:	AT [cmds] %Dn [cmds]
Description:	Controls clear down signal
Command		Function
%D0		Disable clear down signal
í %D1		Enable clear down signal

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
í %C1	Data compression enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP mode enabled
\N3	MNP reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	Reliable mode enabled
í \N6	Auto-reliable mode enabled

CONVERT TO MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \Y [cmds]
Description:	Converts to MNP reliable mode from normal or direct mode

COUNTRY CODE
Type:	Configuration
Format:	AT [cmds] *NCn [cmds]
Description:	Select country code to be used
Command		Function
0		Austria
1		Belgium
2		Denmark
3		Finland
4		France
5		Germany
6		Ireland
7		Italy
8		Luxembourg
9		Netherlands
10		Norway
11		Portugal
12		Spain
13		Sweden
14		Switzerland
15		United Kingdom
16		New Zealand
17		Australia

DISPLAY PASSWORD
Type:	Configuration
Format:	AT [cmds] \P=? [cmds]
Description:	Displays a password from non-volatile memory
Note: NO PASSWORD SAVED is returned if no password was saved.

ECHO DATA
Type:	Configuration
Format:	AT [cmds] \En [cmds]
Description:	Enables modem to echo received data
Command	Function
í \E0	Data echo disabled
\E1	Data echo enabled

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes
Command	Function
\V0	Extended result codes/DCE speed disabled
í \V1	Extended result codes/DCE speed enabled
\V2	Extended result codes/DTE speed disabled
\V3	Extended result codes/DTE speed enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	Bi-directional XON/XOFF flow control enabled
\Q2	CTS flow control by DCE enabled
í \Q3	Bi-directional RTS/CTS flow control enabled
\Q4	Unidirectional XON/XOFF flow control by DCE enabled

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

INITIATE MNP RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \O [cmds]
Description:	Initiates MNP reliable mode from normal or direct mode

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

PASSWORD
Type:	Configuration
Format:	AT [cmds] \P=n [cmds]
Description:	Stores a password in non-volatile memory
Note: Maximum of 7 characters and password is not case sensitive.

POWER-ON AUTO-CONNECT
Type:	Configuration
Format:	AT [cmds] %Pn [cmds]
Description:	Controls power-on auto-connect
Command		Function
í %P0		Disabled power-on auto-connect
%P1		Enabled power-on auto-connect

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product identification code
I1	Reports ROM checksum
I2	Internal memory test
I3	Reports V.42bis ID
I4	Reports internal ID
I90	Report country code

SECURITY CALL-BACK
Type:	Configuration
Format:	AT [cmds] %Sn [cmds]
Description:	Controls security call-back
Command		Function
í %S0		Disabled security call-back
%S1		Enabled security call-back
%S2		Password security check only

SWITCH TO NORMAL MODE
Type:	Immediate
Format:	AT [cmds] \Z [cmds]
Description:	Switches to normal mode from MNP mode

TRANSMISSION LEVEL
Type	Configuration
Format	AT [cmds] %Ln [cmds]
Default	12
Range	0-15
Unit	-1 dBm
Description	Sets the signal level for transmission

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
í \X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem