Card Type	Modem (asynchronous)
Chipset	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation	ITU-T V.17, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10EC, V.42, V.42bis
Fax Class	Class I & II
Data Bus	Serial

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
TM	Red	On	Modem is in test mode
TM	Red	Off	Modem is not in test mode
TD	Red	Blinking	Modem is transmitting data
TD	Red	Off	Modem is not transmitting data
RD	Red	Blinking	Modem is receiving data
RD	Red	Off	Modem is not receiving data
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
AA	Red	Blinking	Phone is ringing
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
CP	Red	On	Compression enabled
CP	Red	Off	Compression disabled
EC	Red	On	Error correction enabled
EC	Red	Off	Error correction disabled
POWER	Red	On	Power is on
POWER	Red	Off	Power is off

MISCELLANEOUS TECHNICAL NOTES

Diagram not available.

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &Q, &R, &S, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \L, \N, \V

%C, %E, %L, %Q

Special AT Commands

:E, -K

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S29, S30, S32, S33, S38

S48, S82, S86, S95

Note: See MHI help file for complete information.

UNIDENTIFIED COMMANDS
Command	Default
\K	Unidentified
*S	Unidentified

MNP10EC MODE
Type:	Configuration
Format:	AT [cmds] -SEC=n [cmds]
Description:	Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.
Command		Function
-SEC=0		MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.
í -SEC=1		MNP10EC handshaking enabled.

PROTOCOL/SPEED
Type:	Configuration
Format:	AT [cmds] Fn [cmds]
Description:	Selects the protocol and speed the modem will attempt to connect at.
Command	Function
F0	Auto-detect the highest common connect speed.
F1	Select V.21 or Bell 103 at 300bps speed.
F3	Select V.23 at 75/1200bps speed.
F4	Select V.22 or Bell 212A at 1200bps speed.
F5	Select V.22bis at 2400bps speed.
F6	Select V.32 or V.32bis at 4800bps speed.
F7	Select V.32bis at 7200bps speed.
F8	Select V.32bis or V.32 at 9600bps speed.
F9	Select V.32bis at 12Kbps speed.
F10	Select V.32bis at 14.4Kbps speed.