...because we can't all be on the bleeding edge...





BITSURFR PRO EZ

MOTOROLA, INC.

BITSURFR PRO EZ

Card Type

ISDN TA

Chip Set

Unidentified

I/O Options

Analog adapters (2)

Transfer Rate

56Kbps x 2/64Kbps x 2

Data Bus

Serial

ISDN Protocol

AIMux, PPP, V.120

Switch Type

5ESS, DMS-100, NI-1

CONNECTIONS

Function

Label

Function

Label

DC power in

CN1

Analog adapter 2

CN4

Serial port

CN2

Analog adapter 1

CN5

ISDN U interface

CN3

   

USER CONFIGURABLE SETTINGS

Setting

Label

Position

í Factory configured - do not alter

SW1/1

Off

í Factory configured - do not alter

SW1/2

Off

í Factory configured - do not alter

SW1/3

Off

í Normal operation

SW1/4

Off

TA will reset to factory defaults when powered up

SW1/4

On

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

LS

Red

On

Power is on

LS

Green

On

TA is ready for operation

LS

Red/Green

Blinking

ISDN not synchronized

LS

N/A

Off

Power is off

1

Green

On

Call is connected on analog adapter 1

1

Green

Blinking

Call is being connected on analog adapter 1

1

Green

Off

Analog adapter 1 is idle

2

Green

On

Call is connected on analog adapter 2

2

Green

Blinking

Call is being connected on analog adapter 2

2

Green

Off

Analog adapter 2 is idle

DTE

Green

On

Data call connected with V.120

DTE

Green

Slow blink

Data call being connected

DTE

Green

Blinking

Data call connected with single-channel protocol

DTE

Green

Fast blink

Data call connected with multi-channel protocol

DTE

Green

Off

Data call not connected

RD

Unidentified

On

TA is receiving data

RD

Unidentified

Off

TA is not receiving data

TD

Unidentified

On

TA is transmitting data

TD

Unidentified

Off

TA is not transmitting data

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, A/

A, E, H, O, V, W, X, Z

&F, &S, &W, &Y, &Z

Extended AT Commands

\Q

S-Registers

S0, S1, S2, S3, S4, S5, S7, S10, S12, S18, S25

Note: See MHI help file for complete information.

Proprietary AT Command Set

BEARER CHANNEL - DATA

Type:

Configuration

Format:

AT [cmds] %A98=x [cmds]

Description:

Selects the Bearer Channel the TA will use for data calls.

Command

Function

%A98=A

TA will use 3.1KHz audio Bearer Channel.

í %A98=D

TA will use data Bearer Channel.

%A98=S

TA will use speech Bearer Channel.

BEARER CHANNEL - ANALOG ADAPTER 1

Type:

Configuration

Format:

AT [cmds] *1%A98=x [cmds]

Description:

Selects the Bearer Channel the TA will use for calls that are made with analog adapter 1.

Command

Function

*1%A98=A

TA will use 3.1KHz audio Bearer Channel.

í *1%A98=S

TA will use speech Bearer Channel.

BEARER CHANNEL - ANALOG ADAPTER 2

Type:

Configuration

Format:

AT [cmds] *2%A98=x [cmds]

Description:

Selects the Bearer Channel the TA will use for calls that are made with analog adapter 2.

Command

Function

*2%A98=A

TA will use 3.1KHz audio Bearer Channel.

í *2%A98=S

TA will use speech Bearer Channel.

CALL ANSWERING - 3.1KHz AUDIO

Type:

Configuration

Format:

AT [cmds] %A94=x [cmds]

Description:

Selects whether the TA will auto-answer incoming calls using the 3.1KHz audio Bearer Channel.

Command

Function

í %A94=D

TA will not answer call.

%A94=E

TA will answer call.

CALL ANSWERING - DATA

Type:

Configuration

Format:

AT [cmds] %A95=x [cmds]

Description:

Selects whether the TA will auto-answer incoming calls using the data Bearer Channel.

Command

Function

%A95=D

TA will not answer call.

í %A95=E

TA will answer call.

CALL ANSWERING - SPEECH BEARER

Type:

Configuration

Format:

AT [cmds] %A93=x [cmds]

Description:

Selects whether the TA will auto-answer incoming calls using the speech Bearer Channel.

Command

Function

í %A93=D

TA will not answer call.

%A93=E

TA will answer call.

CALL BUNDLING

Type:

Configuration

Format:

AT [cmds] @B0=n [cmds]

Description:

Selects whether the TA will make two-channel ISDN data calls.

Command

Function

í @B0=1

Call bundling disabled.

@B0=2

Call bundling enabled.

CALLER ID

Type:

Immediate

Format:

AT [cmds] @Ln [cmds]

Description:

Displays or clears the Caller ID log.

Command

Function

@L0

Clears the Caller ID log.

@L1

Displays the most recent Caller ID entry.

@L2

Displays all Caller ID entries.

CALLER ID AUTO-DISPLAY

Type:

Configuration

Format:

AT [cmds] @N1=n [cmds]

Description:

Selects whether the TA will automatically display Caller ID information upon receiving an incoming call.

Command

Function

í @N1=0

Caller ID auto-display disabled.

@N1=1

Caller ID auto-display enabled.

CALLER ID LOGGING

Type:

Configuration

Format:

AT [cmds] @N0=n [cmds]

Description:

Selects whether the TA will log Caller ID information.

Command

Function

í @N0=0

Caller ID logging disabled.

@N0=1

Caller ID logging enabled.

CALLER ID SECURITY

Type:

Configuration

Format:

AT [cmds] @IS=x [cmds]

Description:

Selects which type of security will be used with the Caller ID database.

Command

Function

@IS=B

Call blocking enabled.

í @IS=D

Call security disabled.

@IS=S

Call screening enabled.

CALLER ID SECURITY - ADD

Type:

Configuration

Format:

AT [cmds] @IA=<#> [cmds]

Description:

Adds the number specified to the Caller ID security list.

CALLER ID SECURITY - CLEAR

Type:

Configuration

Format:

AT [cmds] @IC [cmds]

Description:

Clears the Caller ID security table.

CALLER ID SECURITY - COPY TO DATA PORTS

Type:

Configuration

Format:

AT [cmds] @IP [cmds]

Description:

Copies the Caller ID security table to all data ports.

CALLER ID SECURITY - COPY TO VOICE PORTS

Type:

Configuration

Format:

AT [cmds] @IV [cmds]

Description:

Copies the Caller ID security table to all voice ports.

CALLER ID SECURITY - DELETE

Type:

Configuration

Format:

AT [cmds] @ID=<#> [cmds]

Description:

Deletes the number specified from the Caller ID security list.

CALLER ID SECURITY - DISPLAY

Type:

Immediate

Format:

AT [cmds] @IL [cmds]

Description:

Displays the Caller ID security table.

CHAP PASSWORD

Type:

Configuration

Format:

AT [cmds] @M20="xxxx" [cmds]

Description:

Sets the password the TA will send at connection for CHAP authentication if CHAP authentication is requested and no password is provided within the dialing command.

CONFIGURATION WRITE PROTECTION

Type:

Configuration

Format:

AT [cmds] @G=x [cmds]

Description:

Selects whether the user may store changes to the TA's configuration.

Command

Function

í @G=D

Write protection disabled.

@G=E

Write protection enabled.

DATA LENGTH

Type:

Configuration

Format:

AT [cmds] @P4=n [cmds]

Description:

Sets the length of the data words the TA is receiving from the serial port.

Command

Function

@P4=7

TA uses seven data bits.

í @P4=8

TA uses eight data bits.

DATA PARITY

Type:

Configuration

Format:

AT [cmds] @P3=x [cmds]

Description:

Sets the parity of the data the TA is receiving from the serial port.

Command

Function

@P3=E

TA uses even parity.

@P3=M

TA uses mark parity.

í @P3=N

TA uses no parity.

@P3=O

TA uses odd parity.

DATA STOP

Type:

Configuration

Format:

AT [cmds] @P6=n [cmds]

Description:

Sets the number of stop bits the TA is receiving from the serial port.

Command

Function

í @P6=0

TA uses one stop bit.

@P6=1

TA uses one and one half stop bits.

@P6=2

TA uses two stop bits.

DCD SIGNAL

Type:

Configuration

Format:

AT [cmds] &Cn [cmds]

Description:

Configures the behaviour of the DCD signal.

Command

Function

&C0

DCD forced high.

í &C1

DCD normal.

&C2

DCD forced high except during disconnect.

DIAL

Type:

Immediate

Format:

AT [cmds] D<#>;[cmds]

Description:

Dials the telephone number indicated according to any modifiers included in the string.

Command

Function

DS=n

Dial stored telephone number n.

D>P="xxxx"

Dial and send CHAP password xxxx.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DIAL MODE

Type:

Configuration

Format:

AT [cmds] %A97=x [cmds]

Description:

Selects the type of dialing the TA will use.

Command

Function

í %A97=E

Enbloc dialing enabled.

%A97=O

Overlap dialing enabled.

DIRECTORY NUMBER - DATA

Type:

Configuration

Format:

AT [cmds] !N1=<#> [cmds]

Description:

Sets the DN for data calls.

DIRECTORY NUMBER - ANALOG ADAPTER 1

Type:

Configuration

Format:

AT [cmds] *1!N1=<#> [cmds]

Description:

Sets the DN for analog adapter 1.

DIRECTORY NUMBER - ANALOG ADAPTER 2

Type:

Configuration

Format:

AT [cmds] *2!N1=<#> [cmds]

Description:

Sets the DN for analog adapter 2.

DISPLAY COMMAND SETTINGS

Type:

Immediate

Format:

AT [cmds] >V=x [cmds]

Description:

Displays the specified command settings.

Command

Function

>V=C

Displays ISDN switch configuration.

>V=G

Displays global command settings.

DISPLAY COMMAND SETTINGS

Type:

Immediate

Format:

AT [cmds] &V=x [cmds]

Description:

Displays the specified command settings.

Command

Function

&V

Displays port settings.

&V=E

Displays V.120 command settings.

&V=Z

DIsplays stored telephone numbers.

DISPLAY FIRMWARE VERSION

Type:

Immediate

Format:

AT [cmds] $Q [cmds]

Description:

Displays the firmware version number.

DISPLAY HELP SCREEN

Type:

Immediate

Format:

AT [cmds] &H=xxxx,xxxx,xxxx... [cmds]

Description:

Displays the help screen for the command or commands indicated. If no commands are listed, a generic help screen of a list of all supported commands will be displayed.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Displays product identification code.

I1

Displays ROM checksum.

I2

Tests and displays ROM checksum result.

I3

Displays board number, firmware revision, and checksum result.

I4

Displays product ID, supported protocols, firmware date and revision in numeric format.

I8

Displays product ID, supported protocols, firmware date and revision.

I9

Displays Plug-N-Play information.

I10

Displays ISDN connection information.

DTR DIALING

Type:

Configuration

Format:

AT [cmds] &Ln [cmds]

Description:

Selects whether the TA will automatically dial the first stored number when DTR is low and no call is connected.

Command

Function

í &L0

DTR dialing disabled.

&L1

DTR dialing enabled.

DTR SIGNAL

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Configures the behavior of the DTR signal.

Command

Function

&D0

DTR forced high.

&D1

TA will enter command mode on low DTR.

í &D2

TA will disconnect on low DTR.

&D3

TA will disconnect and reset on low DTR.

&D9

DTR dialing enabled.

ECHO CANCELLATION TONE

Type:

Configuration

Format:

AT [cmds] %A96=n [cmds]

Description:

Selects whether the TA will generate an echo cancellation tone.

Command

Function

í %A96=0

Echo cancellation tone disabled.

%A96=1

Echo cancellation tone enabled.

FACTORY DEFAULT PROFILE - ISDN SWITCH

Type:

Configuration

Format:

AT [cmds] >F [cmds]

Description:

Returns the command settings pertaining to the ISDN switch configuration to the values found in the factory default profile.

FIRMWARE UPGRADE

Type:

Immediate

Format:

AT [cmds] $Y=xxxxxx [cmds]

Description:

Begins a firmware upgrade session with the password indicated.

FIRMWARE UPGRADE PASSWORD

Type:

Configuration

Format:

AT [cmds] %P1=xxxxxxxx [cmds]

Description:

Sets the password required to upgrade the firmware to the string indicated. The password must be eight characters or less, case sensitive. If the password is set to a capital D, the password check will be disabled.

ISDN FEATURE - CONFERENCE CALL

Type:

Configuration

Format:

AT [cmds] !V3=n [cmds]

Default:

60

Range:

1 - 63

Unit:

N/A

Description:

Selects the ISDN feature code for conference calling.

ISDN FEATURE - DROP CALL

Type:

Configuration

Format:

AT [cmds] !V4=n [cmds]

Default:

62

Range:

1 - 63

Unit:

N/A

Description:

Selects the ISDN feature code for call dropping.

ISDN FEATURE - TRANSFER CALL

Type:

Configuration

Format:

AT [cmds] !V5=n [cmds]

Default:

61

Range:

1 - 63

Unit:

N/A

Description:

Selects the ISDN feature code for call transferring.

ISDN FEATURE - VOICEMAIL WAITING

Type:

Configuration

Format:

AT [cmds] !V8=n [cmds]

Default:

63

Range:

1 - 63

Unit:

N/A

Description:

Selects the ISDN feature code for waiting voicemail.

LINE SPEED

Type:

Configuration

Format:

AT [cmds] %A4=n [cmds]

Description:

Selects the speed at which the TA will connect.

Command

Function

í %A4=0

Line speed set to 64Kbps.

%A4=1

Line speed set to 56Kbps.

LOCAL SERIAL PORT SPEED

Type:

Configuration

Format:

AT [cmds] @P2=n [cmds]

Description:

Sets the speed of the local serial port.

Command

Function

@P2=300

Sets serial port speed to 300bps.

@P2=1200

Sets serial port speed to 1200bps.

@P2=2400

Sets serial port speed to 2400bps.

@P2=4800

Sets serial port speed to 4800bps.

@P2=9600

Sets serial port speed to 9600bps.

@P2=19200

Sets serial port speed to 19.2Kbps.

@P2=38400

Sets serial port speed to 38.4Kbps.

@P2=57600

Sets serial port speed to 57.6Kbps.

í @P2=115200

Sets serial port speed to 115.2Kbps.

@P2=230400

Sets serial port speed to 230.4Kbps. This disables serial port speed auto-detection.

PROTOCOL - B-CHANNEL

Type:

Configuration

Format:

AT [cmds] %A2=n [cmds]

Description:

Selects the rate adaptation protocol the TA will use.

Command

Function

%A2=2

V.120 protocol selected.

%A2=3

PPP protocol selected.

í %A2=95

AIMux protocol selected.

RESULT CODES

Type:

Configuration

Format:

AT [cmds] Qn [cmds]

Description:

Enables TA to send result codes to the DTE.

Command

Function

í Q0

Result codes enabled.

Q1

Result codes disabled.

Q2

Result codes enabled in originate mode only.

SERVICE PROFILE ID - DATA

Type:

Configuration

Format:

AT [cmds] !C6=<#> [cmds]

Description:

Sets the SPID for data calls.

SERVICE PROFILE ID - ANALOG ADAPTER 1

Type:

Configuration

Format:

AT [cmds] *1!C6=<#> [cmds]

Description:

Sets the SPID for analog adapter 1.

SERVICE PROFILE ID - ANALOG ADAPTER 2

Type:

Configuration

Format:

AT [cmds] *2!C6=<#> [cmds]

Description:

Sets the SPID for analog adapter 2.

SET DATE

Type:

Configuration

Format:

AT [cmds] >D0=mm/dd/yy [cmds]

Description:

Sets the internal clock to the date specified.

SET TIME

Type:

Configuration

Format:

AT [cmds] >D1=hh:mm:ss [cmds]

Description:

Sets the internal clock to the time specified.

SOFT RESET

Type:

Immediate

Format:

AT [cmds] >Z [cmds]

Description:

Resets TA and command settings pertaining to the ISDN switch configuration to the stored profile.

STORE ISDN SWITCH CONFIGURATION

Type:

Configuration

Format:

AT [cmds] >W [cmds]

Description:

Writes the values for the commands pertaining to the ISDN switch configuration into the non-volatile RAM.

SWITCH TYPE

Type:

Configuration

Format:

AT [cmds] !C0=n [cmds]

Description:

Selects the type of ISDN switch the TA is connected to.

Command

Function

!C0=0

TA is connected to AT&T 5ESS switch.

!C0=1

TA is connected to Northern Telecom DMS-100 switch.

í !C0=2

TA is connected to National NI-1 switch.

SWITCH VERSION

Type:

Configuration

Format:

AT [cmds] !C1=n [cmds]

Description:

Selects the version of ISDN switch the TA is connected to.

Command

Function

!C1=0

TA is connected to 5ESS point-to-point switch.

!C1=1

TA is connected to 5ESS multipoint switch.

!C1=2

TA is connected to DMS-100 PVC IC-0 switch.

!C1=3

TA is connected to DMS-100 PVC IC-1 switch.

í !C1=4

TA is connected to NI-1 switch.

TERMINAL ENDPOINT IDENTIFIER - DATA

Type:

Configuration

Format:

AT [cmds] !D3=n [cmds]

Default:

255

Range:

0 - 63, 127, 255

Unit:

N/A

Description:

Selects the TEI for data calls. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI.

TERMINAL ENDPOINT IDENTIFIER - ANALOG ADAPTER 1

Type:

Configuration

Format:

AT [cmds] *1!D3=n [cmds]

Default:

255

Range:

0 - 63, 127, 255

Unit:

N/A

Description:

Selects the TEI for analog adapter 1. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI.

TERMINAL ENDPOINT IDENTIFIER - ANALOG ADAPTER 2

Type:

Configuration

Format:

AT [cmds] *2!D3=n [cmds]

Default:

255

Range:

0 - 63, 127, 255

Unit:

N/A

Description:

Selects the TEI for analog adapter 1. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI.

TEST MODES

Type:

Immediate

Format:

AT [cmds] &Tn

Description:

Selects test options.

Command

Function

&T0

End current test.

&T1

Begin local analog loopback test.

&T3

Begin local digital loopback test.

&T8

Begin bilateral loopback est

&T9

Begin terminal loopback test.

V.120 MAXIMUM RECEIVE FRAME SIZE

Type:

Configuration

Format:

AT [cmds] %E1=n [cmds]

Default:

256

Range:

1 - 260

Unit:

1 byte

Description:

Sets the maximum frame size for transmission in V.120 mode.

V.120 MAXIMUM TRANSMIT FRAME SIZE

Type:

Configuration

Format:

AT [cmds] %E0=n [cmds]

Default:

256

Range:

1 - 260

Unit:

1 byte

Description:

Sets the maximum frame size for transmission in V.120 mode.

V.120 TRANSMISSION TIMER

Type:

Configuration

Format:

AT [cmds] %E3=n [cmds]

Default:

5

Range:

1 - 255

Unit:

Unidentified

Description:

Sets the T200 transmission timer for V.120 mode.

V.120 WINDOW SIZE

Type:

Configuration

Format:

AT [cmds] %E2=n [cmds]

Default:

8

Range:

1 - 127

Unit:

1 byte

Description:

Sets the window size for V.120 mode.