...because we can't all be on the bleeding edge...





PNIC3000

MAXTECH CORPORATION

PNIC3000

Card Type

Modem (asynchronous), Ethernet

Chipset

Unidentified

Boot ROM

Not available

Network Transfer Rate

10Mbps

Topology

Star

Wire Type

Unshielded twisted pair

Maximum Data Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

Bell 103A, 212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10EC, V.42, V.42bis

Fax Class

Class I & II

Data Bus

PCMCIA Type II

53752

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &P, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \L, \N, \V

%C, %E, %L, %Q

Special AT Commands

#CID, :E, *H, -K, )M, @M, +MS, -Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S24, S25, S26, S29, S30, S32, S33

S38, S46, S48, S82, S86, S91, S92, S95, S201

Note: See MHI help file for complete information.

UNIDENTIFIED COMMANDS

Command

Default

\K

5

S14

Unidentified

S16

Unidentified

S21

Unidentified

S22

Unidentified

S23

Unidentified

S27

Unidentified

S28

Unidentified

S31

Unidentified

S36

7

S37

0

S39

3

S40

107

S41

3

Proprietary AT Command Set

DIAL

Type:

Immediate

Format:

AT [cmds] D<#>;[cmds]

Description:

Dials the telephone number indicated according to any modifiers included in the string.

Command

Function

DJ

MNP10 link will be negotiated at 1200bps for this call.

DK

MNP10 power level adjustment enabled for this call.

DL

Re-dial last number.

DP

Pulse dialing enabled.

DS=n

Dial stored telephone number n.

DT

Tone dialing enabled.

DW

Dialing resumed following dial tone detection.

D,

Dialing paused for amount of time specified in S8 register.

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

&

Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Displays product identification code.

I1

Performs ROM testing.

I2

Performs RAM testing.

I3

Displays firmware revision.

I4

Displays internal factory ID.

I6

Displays data pump version.

I7

Displays DAA code.

MNP10EC MODE

Type:

Configuration

Format:

AT [cmds] -SEC=n [cmds]

Description:

Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.

Command

Function

-SEC=0

MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.

í -SEC=1

MNP10EC handshaking enabled.