...because we can't all be on the bleeding edge...





336IFXSP(C)

NEWCOM, INC.

336IFXSP(C)

Card Type

Modem (asynchronous)

Chipset

Unidentified

I/O Options

Audio line out, microphone in, speaker out, voice, speakerphone

Maximum Data Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

Bell 103A, 212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

Fax Modulation

ITU-T V.17, V.21CH2, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

16-bit ISA

Card Size

Full height, half length

CONNECTIONS

Function

Label

Function

Label

Telephone line out

CN1

Headphone line out

CN4

Telephone line in

CN2

Speaker out

CN5

Microphone in

CN3

   

PLUG-N-PLAY

Setting

JP1/A

JP1/B

JP1/C

í Enabled

Closed

Closed

Closed

Disabled

Open

Open

Open

Note: If Plug-N-Play mode is enabled, all other jumper settings must also be set for Plug-N-Play.

INTERRUPT SELECTION

Setting

JP1/D

JP1/E

JP1/F

JP1/G

JP1/H

JP1/I

JP1/J

3

Open

Open

Open

Open

Open

Open

Closed

4

Open

Open

Open

Open

Open

Closed

Open

5

Open

Open

Open

Open

Closed

Open

Open

7

Open

Open

Open

Closed

Open

Open

Open

10

Closed

Open

Open

Open

Open

Open

Open

11

Open

Closed

Open

Open

Open

Open

Open

12

Open

Open

Closed

Open

Open

Open

Open

í Plug-N-Play

Closed

Closed

Closed

Closed

Closed

Closed

Closed

SERIAL PORT ADDRESS SELECTION

Setting

JP1/K

JP1/L

JP1/M

JP1/N

3F8h (COM1:)

Closed

Closed

Open

Open

2F8h (COM2:)

Closed

Open

Open

Closed

3E8h (COM3:)

Open

Closed

Closed

Open

2E8h (COM4:)

Open

Open

Closed

Closed

í Plug-N-Play

Open

Open

Open

Open

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, C, D, E, F, H, L, M, N, O, P, Q, T, V, X, Y, Z

&C, &D, &F, &G, &J, &K, &P, &S, &T, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \N, \O, \Q, \T, \U, \X, \Y, \Z

%A, %C, %E, %G

Special AT Commands

-C, "H, -J, "O

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S27

S30, S31, S33, S37

Note: See MHI help file for complete information.

IS-101 COMMANDS

+V Commands

+VBT, +VCID, +VCSD, +VDR, +VEM, +VGM, +VGR, +VGS, +VGT, +VIP, +VIT, +VLS, +VNH, +VRA, +VRN

+VRX, +VSD, +VSM, +VSP, +VTD, +VTS, +VTX, #VSPS

-S Commands

-SAC, -SCD, -SDA, -SDS, -SER, -SFX, -SIC, -SIP, -SQR, -SSP, -SSQ, -SSR, -SSV

Note: The functions of the IS-101 commands are unidentified.

Proprietary AT Command Set

BREAK TYPE

Type:

Configuration

Format:

AT [cmds] \Kn [cmds]

Description:

Configures action of break signal.

Command

Break from DTE

Reliable/Normal mode

Break from DTE

Direct mode

Modem receives \B

Break from remote modem

\K0

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Buffers cleared and break sent to remote modem.

Buffers cleared and break sent to DTE.

\K1

Buffers cleared and break sent to remote modem.

Send break to remote modem immediately.

Buffers cleared and break sent to remote modem.

Buffers cleared and break sent to DTE.

\K2

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Send break to remote modem immediately.

Send break to DTE immediately.

\K3

Send break to remote modem immediately.

Send break to remote modem immediately.

Send break to remote modem immediately.

Send break to DTE immediately.

\K4

Enter command mode, do not send break to remote modem.

Send break to remote modem immediately, then enter command mode.

Send break to remote modem with transmitted data.

Break sent with received data to the DTE.

\K5

Send break with transmitted data.

Send break to remote modem immediately.

Send break to remote modem with transmitted data.

Break sent with received data to the DTE.

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Bn [cmds]

Description:

Selects the communication protocol for low-speed data calls.

Command

Protocol

B0

Modem will use ITU-T V.22 at 1200bps.

í B1

Modem will use Bell 212A at 1200bps.

B2

Modem will use ITU-T V.23 at 1200/75bps.

B3

Modem will use ITU-T V.23 at 75/1200bps.

DISPLAY INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested about the modem.

Command

Function

I0

Displays product identification code.

I1

Displays chip firmware revision.

I2

Tests and displays ROM checksum result.

I3

Displays modem chipset name.

I5

Displays hardware configuration.

I6

Displays country code.

I7

Displays board firmware revision.

I8

Displays chipset feature bitmap.

I10

Displays board feature bitmap.

I11

Displays board feature bitmap.

I14

Displays digital SAFE device information.

I20

Displays the revision level of the modem's voice chipset.

I21

Displays the revision level of the modem's voice firmware.

I22

Displays the voice chipset manufacturer’s name.

I23

Displays the model name of the modem's voice chipset.

DISPLAY PROFILES

Type:

Immediate

Format:

AT [cmds] &Vn [cmds]

Description:

Displays active and stored configuration profiles.

Command

Function

í &V0

Displays stored profile 0.

&V1

Displays stored profile 1.

&V3

Displays relay status and I/O information.

EXTENDED RESULT CODES

Type:

Configuration

Format:

AT [cmds] Wn [cmds]

Description:

Selects which result codes the modem will report.

Command

Function

í W0

Enables CONNECT result codes to report DTE speed.

W1

Enables CONNECT result codes to report DTE speed.

W2

Enables CONNECT result codes to report DCE speed.

W3

Enables CONNECT result codes to report DTE speed with error correction and compression information.

W4

Enables CONNECT result codes to report DTE speed with modulation protocol, error correction, and compression information.

MODE SELECTION

Type:

Immediate

Format:

AT [cmds] +FCLASS=n

Description:

Sets what mode the modem will operate in.

Command

Function

+FCLASS=0

Data mode.

+FCLASS=1

Class 1 fax mode.

+FCLASS=8

Voice mode.

+FCLASS=80

IS-101 voice mode.

TRELLIS CODING

Type:

Configuration

Format:

AT [cmds] &Un [cmds]

Description:

Selects whether the modem will use trellis coding.

Command

Function

í &U0

Trellis coding enabled.

&U1

Trellis coding disabled.