...because we can't all be on the bleeding edge...





XPV 336ER (DSF1133V/R16-PNP)

MAXTECH CORPORATION

XPV 336ER (DSF1133V/R16-PNP)

Card Type

Modem, Fax

Chip Set

Unidentified

I/O Options

Line in, line out, microphone in, speaker out, serial port (RS-232), DC power

Maximum Modem Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34

Fax Modulation Protocol

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I

Data Bus

External

CONNECTIONS

Function

Label

Function

Label

Line out

CN1

Serial port

CN5

Line in

CN2

DC Power

CN6

Microphone in

CN3

Power switch

SW1

Speaker out

CN4

   

DIAGNOSTIC LED(S)

LED

Color

Status

Condition

TST

Unidentified

Blinking

Modem is either in test mode or is resending data

TST

Unidentified

Off

Modem is not in test mode or resending data

HS

Unidentified

On

Communicating at 2400bps or above

HS

Unidentified

Off

High speed transmission is disabled

AA

Unidentified

On

Auto-answer is enabled

AA

Unidentified

Blinking

Ring is detected

AA

Unidentified

Off

No line activity detected

CD

Unidentified

On

The modem detects carrier signal from remote modem

CD

Unidentified

Off

The modem cannot detect carrier signal from remote modem

OH

Unidentified

On

Modem is preparing to dial

OH

Unidentified

Off

Modem is not dialing

RD

Unidentified

On

Data is being sent to the computer via the modem

RD

Unidentified

Off

Data is not being sent from the modem to the computer

SD

Unidentified

On

Data is being received by the modem via the computer

SD

Unidentified

Off

The modem is not receiving data from the computer

TR

Unidentified

On

Modem is ready to receive commands

TR

Unidentified

Off

Modem is not ready to receive commands

MR

Unidentified

On

Modem is turned on

MR

Unidentified

Off

Modem is turned off

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &F, &P, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \K, \N

%C, %L, %Q

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92,

S95

Special Commands

+MS, -SMS=X,Y,Z,T, -SSE=x, -SQS=X,Y

 

Voice Commands

#BDR, #CID, #CLS, #MDL?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, #VSDB,

#VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX

 

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

AUTOSCAN MODE

Type:

Immediate

Format:

AT [cmds] Nn [cmds]

Description:

Enables/Disables Autoscan mode

Command

Function

N0

Autoscan mode disabled

í N1

Autoscan mode enabled

CLEAR TO SEND CONFIGURATION

Type:

Configuration

Format:

AT [cmds] &Rn [cmds]

Description:

Configures CTS settings based on the flow control settings

Command

Function

&R0

Reserved

&R1

Sets CTS operation based on flow control requirements

COMMUNICATIONS MODE (ASYNCHRONOUS)

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

í &M0

Asynchronous mode

COMMUNICATIONS MODE (DATA LINK AND FALLBACK)

Type:

Configuration

Format:

AT [cmds] &Qn [cmds]

Description:

Configures data link and fallback options

Command

Function

&Q0

Set Direct data link only

í &Q5

Set V.42 data link with fallback options enabled

&Q6

Set Normal data link only

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

í &D0

Modem does not respond to DTR

&D1

Modem goes to command mode after DTR goes is off

&D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

&D3

Modem is initialized after DTR goes off

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

í &S1

DSR is off while in command mode and set on in on-line mode

FLOW CONTROL

Type:

Immediate

Format:

AT [cmds] &K [cmds]

Description:

Configures flow control settings

Command

Function

&K0

Flow control disabled

í &K3

RTS/CTS hardware flow control enabled

&K4

XON/XOFF software flow control enabled

&K5

Transparent XON/XOFF software flow control enabled

&K6

RTS/CTS & XON/XOFF flow control enabled

GAURD TONE

Type:

Immediate

Format:

AT [cmds] &G [cmds]

Description:

Configures guard tone

Command

Function

&G0

Disable guard tone

&G1

Disable guard tone

&G2

Set guard tone to 1800 Hz.

LINE TYPE

Type:

Configuration

Format:

AT [cmds] &Ln [cmds]

Description:

Selects line type

Command

Line Type

í &L0

Switched line (PSTN/Dial-up)

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports product ID code

I1

Reports ROM checksum

I2

Test and reports internal memory

I3

Reports firmware ID

I4

Reports reserved ID

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

í L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting

Extended AT Command Set

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode and fallback/fall-forward

Command

Function

í %E0

Auto-retrain disabled

%E1

Auto-retrain enabled

Special Command Set

ASVD/DSVD MODE

Type:

Configuration

Format:

-SMS=X,Y,Z,T [cmds]

Description:

Selects ASVD/DSVD mode

Note:

Y, Z, & T are optional parameters that control connection speed

Command

Function

X = 0

Data mode enabled

X = 1

DSVD mode enabled

X = 2

ASVD mode enabled

X = 3

Automatic mode select enabled

ASVD MODULATION

Type:

Configuration

Format:

-SQS=X,Y [cmds]

Description:

Selects ASVD/DSVD mode

Note:

Y enables/disables ASVD automatic modulation

Command

Function

X = 0

V.61 modulation enabled

X = 1

ML144 modulation enabled

X = 2

ML288 modulation enabled

DSVD

Type:

Configuration

Format:

-SSE=n [cmds]

Description:

Enables/disables DSVD