SIIG, INC.
DASH 14.4I FAX/MODEM INTERNAL
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Phone line out |
CN1 |
Phone line in |
CN2 | |||
|
SERIAL PORT ADDRESS | ||||
|
Setting |
JP1/D |
JP1/E |
JP1/F |
JP1/G |
|
COM1 (3F8h) |
Closed |
Open |
Closed |
Open |
|
COM2 (2F8h) |
Open |
Closed |
Closed |
Open |
|
í COM3 (3E8h) |
Closed |
Open |
Open |
Closed |
|
COM4 (2E8h) |
Open |
Closed |
Open |
Closed |
|
INTERRUPT SELECTION | |||
|
Setting |
JP1/A |
JP1/B |
JP1/C |
|
3 |
Closed |
Open |
Open |
|
4 |
Open |
Closed |
Open |
|
í 5 |
Open |
Open |
Closed |
Proprietary AT Command Set
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
í %E0 |
Auto-retrain disabled |
|
%E1 |
Auto-retrain enabled |
|
%E2 |
Auto-fallback/fall-forward enabled |
|
BIT MAPPED REGISTERS | |
|
Register |
Default |
|
S14 |
138 |
|
S16 |
0 |
|
S21 |
0 |
|
S22 |
117 |
|
S23 |
55 |
|
S27 |
73 |
|
S28 |
0 |
|
S31 |
2 |
|
S40 |
105 |
|
S41 |
3 |
|
BREAK TYPE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] \Kn [cmds] | |
|
Description: |
Configures action of break signal | |
|
Command |
Function | |
|
\K0 |
Online command mode enabled, send no break to remote modem | |
|
\K1 |
Break sent to remote modem and buffers cleared | |
|
\K2 |
Online command mode enabled, send no break to remote modem | |
|
\K3 |
Send break to remote modem immediately | |
|
\K4 |
Online command mode enabled, send no break to remote modem | |
|
\K5 |
Send break with transmitted data | |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Modifier |
Function |
|
L |
Re-dial last number |
|
P |
Pulse dialing enabled |
|
R |
Accepted but not acted upon |
|
S=n |
Dial stored telephone number n (n=0-3) |
|
T |
Tone dialing enabled |
|
W |
Dialing resumed following dial tone detection |
|
! |
Modem commanded to go off-hook for specified time before returning on-hook. |
|
@ |
Wait 5 seconds for quiet answer |
|
& |
Waits for prompt tone |
|
, |
Dialing paused for amount of time specified in S8 register |
|
; |
Modem returned to command state after dialing |
|
^ |
Toggles Calling tone enabled/disabled, for current call |
|
FLASH DIAL MODIFIER TIME | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Time the modem will go on-hook upon receiving the ! dial modifier in dial string. |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control |
|
Command |
Function |
|
í \G0 |
Flow control disabled |
|
\G1 |
Flow control enabled |
|
FLOW CONTROL | |
|
Type: |
Register |
|
Format |
AT [cmds] S39? [cmds] |
|
Description: |
Displays the current flow control |
|
Value |
Meaning |
|
0 |
Flow control disabled |
|
í 3 |
RTS/CTS flow control enabled |
|
4 |
XON/XOFF flow control enabled |
|
5 |
Transparent XON/XOFF flow control enabled |
|
6 |
Both RTS/CTS and XON/XOFF flow control enabled |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S30=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
10 seconds |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. S30=0 will disable timer. |
|
LINE SIGNAL LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Returns a value which indicates the received line signal level |
|
LINE SIGNAL QUALITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Q [cmds] |
|
Description: |
Returns a value which indicates line signal quality |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports precomputed checksum |
|
I2 |
Reports ‘OK’ |
|
I3 |
Reports firmware revision |
|
I4 |
Reports OEM defined identifier string |
|
I5 |
Reports country code |
|
I6 |
Reports data pump model and internal code revision |
|
RPI/DTE SPEED | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +Hn [cmds] | |
|
Description: |
Controls Rockwell Protocol Interface processing and DTE speed | |
|
Command |
Function | |
|
+H0 |
RPI disabled | |
|
+H1 |
RPI enabled and set DTE speed to 19.2Kbps | |
|
+H2 |
RPI enabled and set DTE speed to 38.4Kbps | |
|
+H3 |
RPI enabled and set DTE speed to 57.6Kbps | |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S24=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S24=0 will disable timer. |
|
TRANSMISSION LEVEL - FAX | |
|
Type: |
Register |
|
Format: |
AT [cmds] S92=n [cmds] |
|
Default: |
10 |
|
Range: |
0-15 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission while in fax mode |
|
TRANSMISSION LEVEL - PSTN | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S91=n [cmds] |
|
Default |
10 |
|
Range |
10-15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over switched phone lines |