...because we can't all be on the bleeding edge...





BASKING COMBO

SHARK MULTIMEDIA

BASKING COMBO

Card Type

Modem (asynchronous), Sound card

Chip Set

Unidentified

I/O Options

Line in, microphone, speaker out, game/MIDI port

Maximum Modem Rate

56Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.21, V.22A/B, V.22bis, V.23, V.32, V.32bis, V.34, V.FC, K56flex

Fax Modulation Protocol

ITU-T V.17, V.29, V.27ter, V.33, V.21CH2

Error Correction/Compression

MNP5, MNP10, V.42, V.42bis

Fax Class

Class I

Data Bus

16-bit ISA

Card Size

Half-length, half-height card

CONNECTIONS

Function

Label

Function

Label

Line in

CN1

Microphone

CN4

Line out

CN2

Speaker out

CN5

Line in

CN3

Game/MIDI port

CN6

SUPPORTED COMMAND SET

Basic AT Commands

AT, +++, A/

A, E, H, M, O, P, Q, T, V, X

&C, &P, &R, &V, &W, &Z

Extended AT Commands

\A, \B, \K, \N

%C, %E

Voice Commands

#BDR, #CID, #TL, #VBS, #VSD, #VGT

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S18, S25, S26

Special Commands

+MS

Note: See MHI Help File for full command documentation.

 

 

 

Proprietary AT Command Set

AUTOMODE CONTROL

Type:

Immediate

Format:

AT [cmds] Nn [cmds]

Description:

Controls the automode detection

Command

Function

N0

Disabled

N1

Enabled

COMMUNICATION PROTOCOLS

Type:

Configuration

Format:

AT [cmds] Bn [cmds]

Description:

Selects the communication protocol for data calls

Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.

Command

Protocol

B0

ITU-T V.22 at 300 or 1200bps

COMPRESSION

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Selects data compression

Command

Function

&K0

Data compression disabled

&K1

MNP5 enabled

&K2

V.42bis enabled

&K3

MNP5 and V.42bis; or data compression and correction enabled

CONNECT MESSAGE FORMAT

Type:

Configuration

Format:

AT [cmds] &An [cmds]

Description:

Sets the connect message format

Command

Function

í &A0

Only CONNECT message

&A1

CONNECT message and modulation indicator

&A2

CONNECT message, error detection protocol and data compression indicators

&A3

CONNECT message, error detection protocol, data compression indicators and modulation indicator

 

 

 

 

 

 

 

 

CONNECT MESSAGE SPEED SOURCE

Type:

Configuration

Format:

AT [cmds] &En [cmds]

Description:

Sets the requested source for the speed field in the CONNECT message.

Note: Used primarily for international data transmission

Command

Function

í &E0

DCE speed

&E1

DTE speed

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR follows circuit definition

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Command

Function

í &D0

Modem does not respond to DTR

&D1

Modem goes to command mode after DTR goes is off

&D2

Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled.

&D3

Modem is initialized after DTR goes off

DEFAULT CONFIGURATION

Type:

Configuration

Format:

AT [cmds] Yn [cmds]

Description:

Sets the default configuration

Command

Function

í Y0

Select user template 0

Y1

Select user template 1

Y2

Select factory setting 0

Y3

Select factory setting 1

 

 

 

 

 

 

 

 

 

 

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DL

Re-dial last number

DP

Pulse dialing enabled

DS=n

Dial stored telephone number n

DT

Tone dialing enabled/Pulse dialing disabled

DW

Dialing resumed following dial tone detection

D,

Dialing paused for amount of time specified in S8 register

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D*

Tone only

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

FACTORY DEFAULT PROFILE

Type:

Configuration

Format:

AT [cmds] &F [cmds]

Description:

Sets values in active profile to values found in the default profile

Command

Function

í &F0

Select factory setting 0

&F1

Select factory setting 1

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Hn [cmds]

Description:

Sets the flow control

Command

Function

í &H0

Disable flow control

&H1

Enable RTS/CTS emulation

 

 

 

 

 

 

 

 

 

 

 

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I1

Reports modem name, vendor number, version

I2

Reports software vendor and version number

I3

Reports chip vendor, ID number

I4

Reports modem active profile

I5

Reports stored profile 0 and active profile 0

I6

Reports stored profile 1 and active profile 1

I7

Reports stored phone numbers

SOFT RESET

Type:

Immediate

Format:

AT [cmds] Zn [cmds]

Description:

Restores modem profiles previously saved in non-volatile RAM using the &W command.

Command

Function

Z0

Select default user template in Y

Z1

Select user template 0

Z2

Select user template 1

Z3

Select factory setting 0

Z4

Select factory setting 1

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

í L2

Medium volume setting

L3

Highest volume setting

TEST MODES

Type:

Immediate

Format:

AT [cmds] &Tn

Description:

Selects test options

Command

Function

&T0

TBD

&T1

TBD

&T2

TBD

&T3

TBD

 

 

 

STANDARD AT# VOICE COMMAND SET

INACTIVITY TIMER

Type:

Immediate

Format:

AT [cmds] #VIT=n [cmds]

Description:

Sets the inactivity timer

RECEIVE GAIN

Type:

Immediate

Format:

AT [cmds] #RG=n [cmds]

Description:

Sets the receive gainlevel

VOICE PARAMETERS

Type:

Immediate

Format:

AT [cmds] #VIP=n [cmds]

Description:

Initializes the voice parameters

S(status) -REGISTERS

ACTUAL MODULATION

Type:

Register

Format

AT [cmds] S37=n [cmds]

Description:

Returns the actual modulation speed

ACTUAL RX SPEED

Type:

Register

Format

AT [cmds] S38=n [cmds]

Description:

Returns the actual RX speed

ACTUAL SPEED

Type:

Register

Format:

AT [cmds] S35=n [cmds]

Description:

Sets the actual speed after connect

ADPCM

Type:

Register

Format:

AT [cmds] S76=n [cmds]

Default:

4

Range:

4, 8, 16

Description:

Controls the ADPCM bits per sample

 

 

 

 

 

 

ANSWER DELAY

Type:

Register

Format:

AT [cmds] S92=n [cmds]

Default:

2

Range:

0-255

Description:

Controls the answer delay

AUTO ANSWER

Format

AT [cmds] S27=n [cmds]

Default:

8

Range:

0-255

Unit:

1 second

Description:

Sets the auto answer clear timeout

AUTOMODE SELECT

Format:

AT [cmds] S31=n [cmds]

Default:

1

Range:

0-3

Description:

Sets automode

BEEP TONE TIMER

Type:

Register

Format:

AT [cmds] S77=n [cmds]

Default:

10

Range:

0-40

Description:

Sets the beep tone timer

BREAK LENGTH

Format

AT [cmds] S21=n [cmds]

Default:

9

Range:

0-9

Description:

Sets the break length

CD

Type:

Register

Format:

AT [cmds] S60=n [cmds]

Default:

1

Range:

0-1

Description:

Sets the CD setting

CID

Type:

Register

Format:

AT [cmds] S75=n [cmds]

Default:

0

Range:

0,1

Description:

Controls the CID

CIRCUIT 106

Type:

Register

Format:

AT [cmds] S66=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the circuit 106 (RTS)

CIRCUIT 107

Type:

Register

Format:

AT [cmds] S67=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the circuit 107 (DSR)

CIRCUIT 109

Type:

Register

Format:

AT [cmds] S68=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the circuit 109 (CD)

CONNECT MESSAGE

Type:

Register

Format:

AT [cmds] S70=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the CONNECT message format

CONNECT MESSAGE

Type:

Register

Format:

AT [cmds] S71=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the CONNECT message speed source

COUNTRY TYPE

Type:

Register

Format:

AT [cmds] S162=n [cmds]

Default:

1

Range:

0-25

Description:

Sets the country type

 

 

 

 

 

 

CURRENT SETTING

Type:

Register

Format:

AT [cmds] S59=n [cmds]

Default:

3

Range:

0-5

Description:

Sets the current setting

DATA PUMP STATUS

Type:

Register

Format

AT [cmds] S36=n [cmds]

Description:

Displays the current data pump status

DEFAULT SETTING

Type:

Register

Format:

AT [cmds] S161=n [cmds]

Default:

2

Range:

0-1

Description:

Sets the default setting

DSR

Type:

Register

Format:

AT [cmds] S64=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the DSR

DTMF HIGH GAIN

Type:

Register

Format:

AT [cmds] S156=n [cmds]

Default:

0

Range:

0-255

Description:

Sets the DTMF high gain level

DTMF LOW GAIN

Type:

Register

Format:

AT [cmds] S155=n [cmds]

Default:

0

Range:

0-255

Description:

Sets the DTMF low gain level

DTMF TONE

Type:

Register

Format:

AT [cmds] S84=n [cmds]

Default:

0

Range:

0-3F

Description:

Controls the DTMF tone reports cap 0

DTMF TONE

Type:

Register

Format:

AT [cmds] S85=n [cmds]

Default:

0

Range:

0-3F

Description:

Controls the DTMF tone reports cap 1

DTMF TONE

Type:

Register

Format:

AT [cmds] S86=n [cmds]

Default:

0

Range:

0-3F

Description:

Controls the DTMF tone reports cap 2

DTR

Type:

Register

Format:

AT [cmds] S63=n [cmds]

Default:

0

Range:

0-3

Description:

Sets the DTR

ECHO

Type:

Register

Format

AT [cmds] S13=n [cmds]

Default:

1

Range:

0-1

Description:

Sets the echo

EXTENDED CODE

Type:

Register

Format:

AT [cmds] S56=n [cmds]

Default:

4

Range:

0-4

Description:

Sets the extended code

FAE VALUE

Type:

Register

Format:

AT [cmds] S151=n [cmds]

Default:

0

Range:

0,1

Description:

Sets the FAE value

 

 

 

 

 

 

FCLASS VALUE

Type:

Register

Format:

AT [cmds] S150=n [cmds]

Default:

0

Range:

0,1,8

Description:

Sets the FCLASS value

FLASH TIMER

Type:

Register

Format

AT [cmds] S24=n [cmds]

Default:

20

Range:

0-255

Unit:

10 ms

Description:

Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

FLASH TIMER

Type:

Register

Format:

AT [cmds] S140=n [cmds]

Range:

0-255

Description:

Sets the duration of the flash timer

FLOW CONTROL

Type:

Register

Format:

AT [cmds] S62=n [cmds]

Default:

1

Range:

0-3

Description:

Sets the flow control

FLOW CONTROL CHARACTER - XOFF

Type:

Register

Format

AT [cmds] S23=n [cmds]

Default:

19

Range:

0-127

Description:

Sets the XOFF character

HANDSET GAIN

Type:

Register

Format:

AT [cmds] S72=n [cmds]

Default:

80

Range:

0-255

Description:

Sets the handset record gain control

 

 

 

 

 

HSET OUT GAIN

Type:

Register

Format:

AT [cmds] S154=n [cmds]

Range:

0-255

Description:

Sets the Hset out gain level

INACTIVITY TIMER

Type:

Register

Format

AT [cmds] S19=n [cmds]

Default:

0

Range:

0-255

Description:

Sets the system inactivity timer

LINE OUT GAIN

Type:

Register

Format:

AT [cmds] S152=n [cmds]

Range:

0-255

Description:

Sets the line out gain level

LINE QUALITY CONTROL

Type:

Register

Format

AT [cmds] S39? [cmds]

Range:

0-2

Default:

2

Description:

Displays the line quality control

LINE RECORD GAIN

Type:

Register

Format:

AT [cmds] S139=n [cmds]

Range:

0-255

Description:

Sets the line record gain level

LINE SELECTION DURATION

Type:

Register

Format:

AT [cmds] S78=n [cmds]

Default:

0

Description:

Sets the line selection duration

MAX SPEED

Type:

Register

Format:

AT [cmds] S34=n [cmds]

Description:

Sets the requested MAX speed

 

 

 

 

 

MICROPHONE

Type:

Register

Format:

AT [cmds] S90=n [cmds]

Default:

1

Range:

0-3

Description:

Sets the microphone

MICROPHONE GAIN

Type:

Register

Format:

AT [cmds] S138=n [cmds]

Range:

0-255

Description:

Sets the microphone gain level

MIN SPEED

Type:

Register

Format:

AT [cmds] S33=n [cmds]

Description:

Sets the requested MIN speed

ORIGIN/ANSWER

Type:

Register

Format

AT [cmds] S22=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the origin/answer

PLAYBACK

Type:

Register

Format:

AT [cmds] S74=n [cmds]

Default:

153

Range:

0-255

Description:

Sets the playback volume

PROCESSOR TYPE

Type:

Register

Format:

AT [cmds] S193=n [cmds]

Default:

0

Range:

0-100

Description:

Sets the processor type

PULSE MAKE RATIO

Type:

Register

Format:

AT [cmds] S146=n [cmds]

Default:

39

Range:

0-100

Description:

Sets the pulse make ratio

 

 

PULSE PAUSE

Type:

Register

Format:

AT [cmds] S148=n [cmds]

Default:

80

Range:

0-255

Description:

Sets the pulse pause

PULSE PPS

Type:

Register

Format:

AT [cmds] S147=n [cmds]

Default:

10

Range:

10, 20

Description:

Sets the pulse PPS

PULSE REFRESH

Type:

Register

Format:

AT [cmds] S149=n [cmds]

Default:

0

Range:

0-100

Description:

Sets the pulse refresh

PULSE SET?BREAK RATIO

Format

AT [cmds] S28=n [cmds]

Default:

0

Range:

0-4

Description:

Sets the pulse set/break ratio

PULSE TONE

Type:

Register

Format:

AT [cmds] S16=n [cmds]

Default:

1

Range:

0-1

Description:

Sets the pulse tone

QUIET

Type:

Register

Format

AT [cmds] S14=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the quiet function

RECEIVED SIGNAL LEVEL

Format

AT [cmds] S41=n [cmds]

Description:

Displays the received signal level

 

 

 

REQUESTED MODULATION

Format:

AT [cmds] S32=n [cmds]

Default:

8

Range:

Unidentified

Description:

Sets requested modulation

RESULT CODES

Type:

Register

Format:

AT [cmds] S43=n [cmds]

Description:

Controls the result codes

RING GOES AWAY TIMER

Type:

Register

Format:

AT [cmds] S79=n [cmds]

Default:

70

Range:

0-255

Description:

Sets the ring goes away timer

RING NEVER CAME TIMER

Type:

Register

Format:

AT [cmds] S80=n [cmds]

Default:

70

Range:

0-255

Description:

Sets the ring never came timer

RTS

Type:

Register

Format:

AT [cmds] S61=n [cmds]

Default:

0

Range:

0-1

Description:

Sets the RTS

SIGNAL TO NOISE RATIO

Type:

Register

Format:

AT [cmds] S42=n [cmds]

Description:

Controls the signal to noise ratio setting.

SILENCE DETECT

Type:

Register

Format:

AT [cmds] S81=n [cmds]

Default:

0

Range:

0, 1

Description:

Enables and disables the silence detection

 

 

 

 

SILENCE DETECTION

Type:

Register

Format:

AT [cmds] S82=n [cmds]

Default:

2

Range:

0-3

Unit:

0.1 second

Description:

Controls the silence detection sensitivity

SILENCE DETECTION

Type:

Register

Format:

AT [cmds] S83=n [cmds]

Default:

55

Range:

0-255

Description:

Controls the silence detection duration

SPEAKER

Type:

Register

Format:

AT [cmds] S89=n [cmds]

Default:

5

Range:

0-15

Description:

Sets the speaker

SPEAKER CONTROL

Type:

Register

Format

AT [cmds] S29=n [cmds]

Default:

1

Range:

0-3

Description:

Sets the speaker control

SPEAKER MUTE

Type:

Register

Format:

AT [cmds] S88=n [cmds]

Default:

1

Range:

0-2

Description:

Sets the speaker mute

SPEAKER OUT GAIN

Type:

Register

Format:

AT [cmds] S153=n [cmds]

Range:

0-255

Description:

Sets the speaker out gain level

 

 

 

 

 

 

SPEAKER VOLUME

Type:

Register

Format

AT [cmds] S30=n [cmds]

Default:

2

Range:

0-3

Description:

Sets the speaker volume

TIME MARK

Type:

Register

Format:

AT [cmds] S87=n [cmds]

Default:

0

Range:

0-255

Description:

Controls the time mark placement

TRANSMIT LEVEL GAIN

Type:

Register

Format:

AT [cmds] S45=n [cmds]

Default:

3

Range:

0-10

Description:

Controls the result codes

VERBOSE

Type:

Register

Format

AT [cmds] S15=n [cmds]

Default:

1

Range:

0-1

Description:

Sets the verbose function

VOICE SAMPLE

Type:

Register

Format:

AT [cmds] S91=n [cmds]

Default:

0

Range:

1,2

Description:

Sets the voice sample rate