CONNECTIONS
Purpose	Location	Purpose	Location
Line out	CN1	Stored profile	SW2
Line in	CN2	Voice mode	SW3
DC power	CN3	AD/DC	SW4
RS-232/422	CN4	Power switch	SW5
Volume	SW1

STORED PROFILE
Function	SW2
Signal to display active profile	Press
Signal to display menu of stored profiles	Press twice
Note: Function is software dependent.

Voice
Function	Mode	SW3
Dial stored number, speakerphone on	Off line	Press
Microphone disable	Speakerphone	Press

AD/DC
Function	Mode	SW4
Dial stored number	Off line	Press
Disconnect	On line	Press

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
DTR	Red	On	DTR high
DTR	Red	Off	DTR normal
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
OH	Green	On	Speakerphone on
OH	Green	Blinking	Speakerphone on, microphone muted
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
PWR/RI	Red	On	Power on
PWR/RI	Red	Off	Power off
PWR/RI	Red	Blinking	Ring detected
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data

ROAD KEY CUSTOMIZE
Type:	Configuration
Format:	AT [cmds] *A^x^x^x^x [cmds]
Example:	AT *A^M^H^I^I &W<CR>
Description:	Sets the key for Remote Options Access and Downloading (^ indicates ctrl key depressed). The default is ^R^O^A^D.

RING TO SPEAKER
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Example:	AT &J0 *U O<CR>
Description:	Plays ring signal through speaker
Command	Function
&J0	Enabled
» &J1	Disabled

ROAD KEY ENABLE
Type:	Configuration
Format:	AT [cmds] *Bn [cmds]
Example:	AT *B0 *U O<CR>
Description:	Enables Remote Options Access and Downloading.
Command	Function
» *B0	R.O.A.D. disabled.
*B1	R.O.A.D. enabled.

COMPRESSION
Type:	Configuration
Format:	AT %Cn
Example:	AT %C0 *Y1<CR>
Description:	Selects data compression.
Command	Function
» %C3	Data compression and correction enabled.
%C0	Data compression disabled.
%C1	Data compression enabled.
%C2	Data correction enabled.

ID DISPLAY
Type:	Immediate
Format:	AT [cmds] In [cmds]
Example:	AT I1 &W<CR>
Description:	Displays modem properties.
Command	Function
I0	Display product code.
I1	Display checksum.
I2	Display checksum check.
I3	Display version number.

MNP10 COMPRESSION
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Example:	AT %C1 -K1 -Q0 <CR>
Description:	Selects MNP10 data compression.
Command	Function
» -K0	MNP10 disabled.
-K1	MNP10 enabled.
-K2	MNP10 enabled on originate mode only.

CELLULAR PHONE POWER LEVEL
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Example:	AT )M1 %C1<CR>
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation.
Command	Function
» )M0	Power level adjustment disabled.
)M1	Power level adjustment enabled.

MNP10 FALL-BACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Example:	AT *H0 -Q1 <CR>
Description:	Allows MNP10 to fall back to speeds slower than 4800bps.
Command	Function
-Q0	MNP10 at 2400 and 1200bps disabled.
» -Q1	MNP10 at 2400 and 1200bps enabled.

ROAD INITIATE
Type:	Immediate
Format:	AT [cmds] *U [cmds]
Example:	AT *B0 *U O<CR>
Description:	Commands the modem to transmit stored Remote Access Options and Downloading key. The modem must have already connected.