Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP10, V.42bis

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and auto-fallback/fall-forward
Command	Function
í %E0	Auto-retrain disabled
%E1	Auto-retrain enabled
%E2	Auto-fallback/fall-forward enabled
%E3	Auto-retrain enabled with fast hang-up

BIT MAPPED REGISTERS
Register	Default
S14	Unidentified
S16	Unidentified
S21	Unidentified
S22	Unidentified
S23	Unidentified
S27	Unidentified
S28	Unidentified
S31	Unidentified
S40	Unidentified
S41	Unidentified

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Description:	Configures action of break signal

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
í %C3	MNP5 and V.42bis enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
í \N3	Auto-reliable mode enabled
\N4	LAP-M error correcting only enabled
\N5	MNP error correcting only enabled

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Modifier	Function
L	Redials last number
P	Pulse dialing enabled
T	Tone dialing enabled
W	Dialing resumed following dial tone detection
,	Dialing paused for amount of time specified in S8 register
@	Modem waits for a ring-back signal followed by silence up to 5 second prior to executing the rest of the dial string.
R	Command recognized and not initiated
;	Modem returned to command mode after dialing.
!	Flash function initiated. Goes on-hook for amount of time specified in S29 register
S=(0-3)	Number in memory location &Zn dialed
^	Calling tone enabled, data mode only.

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL
Type:	Register
Format:	AT [cmds] S39=n [cmds]
Description:	Select the type of flow control used
Command		Function
S39=0		Flow control disabled
í S39=3		Hardware flow control enabled
S39=4		Software flow control enabled
S39=5		Transparent software flow control enabled
S39=6		Both hardware and software flow control enabled

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns a value which indicates the received line signal level (-dBm)

LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Returns a value which indicates line signal quality

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
í \A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

MNP - STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP link
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

MNP10 - EXTENDED SERVICES
Type:	Configuration
Format:	AT [cmds] -Kn [cmds]
Description:	Selects MNP10 extended services
Command	Function
-K0	MNP10 disabled
í -K1	MNP10 enabled
-K2	MNP10 enabled on originate mode only

MNP10 - FALLBACK
Type:	Configuration
Format:	AT [cmds] -Qn [cmds]
Description:	Allows MNP10 to fall back to speeds slower than 4800bps
Command	Function
-Q0	MNP10 at 2400 and 1200bps disabled
í -Q1	MNP10 at 2400 and 1200bps enabled

MNP10 - LINK NEGOTIATION
Type:	Configuration
Format:	AT [cmds] *Hn [cmds]
Description:	Sets the speed at which MNP10 link negotiation will occur
Command	Function
í *H0	Link will be negotiated at highest possible speed
*H1	Link will be negotiated at 1200bps
*H2	Link will be negotiated at 4800bps

MNP10 - POWER LEVEL ADJUST
Type:	Configuration
Format:	AT [cmds] )Mn [cmds]
Description:	Controls automatic transmit power level adjustment during MNP 10 link negotiation
Command	Function
í )M0	Power level adjustment disabled
)M1	Power level adjustment enabled

TRANSMISSION LEVEL - CELLULAR
Type:	Configuration
Format:	AT [cmds] @Mn [cmds]
Default:	0
Range:	11-31
Unit:	-1 dBm
Description:	Sets the signal level for transmission while in cellular mode
Command	Function
@M0	-26 dBm
@M1	-30 dBm
@M2-@M10	-10 dBm

V.32 - COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :En [cmds]
Description:	Controls V.32 compromise equalizer
Command	Function
:E0	Equalizer disabled
í :E1	Equalizer enabled