...because we can't all be on the bleeding edge...





SATISFAXTION MOBILE PDMCIA9023COMBO

WILDCARD TECHNOLOGIES, INC.

SATISFAXTION MOBILE PDMCIA9023COMBO

Card Type

Modem (asynchronous), Ethernet

Chipset

Intel 82595TX

Maximum Onboard Memory

160KB DRAM/128KB PROM

Network Transfer Rate

10Mbps

Maximum Data Rate

28.8Kbps

Maximum Fax Rate

14.4Kbps

Data Bus

PCMCIA Type II

Fax Class

Class I & II

Data Modulation

Bell 103A/212A

ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation

Unidentified

Error Correction/Compression

MNP5, MNP10, V.42, V.42bis

Topology

Star

Wire Type

Unshielded twisted pair

Boot ROM

Not available

52771

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \J, \K, \L, \N

%C, %L, %Q

Special AT Commands

-K, -Q, *H, )M, @M, :E, +MS

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91,

S92, S95, S201

Proprietary AT Command Set

AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD

Type:

Configuration

Format:

AT [cmds] %En [cmds]

Description:

Controls auto-retrain mode and fallback/fall-forward

Command

Function

í %E0

Auto-retrain disabled.

%E1

Auto-retrain enabled.

%E2

Auto-fallback/fall-forward enabled.

%E3

Auto-retrain and fast disconnect enabled.

AUTOSYNC

Format

AT [cmds] S19=n [cmds]

Default:

0

Range:

0 - 63

Unit:

Bit-mapped

Description:

Sets options for Hayes AutoSync functions.

Bit

Value

Function

0

0

Not used.

1

í 0

1

BSC enabled.

HDLC enabled.

2

í 0

1

HDLC address detection disabled.

HDLC address detection enabled.

3

í 0

1

NRZI bit encoding enabled.

NRZ bit encoding enabled.

4

í 0

1

Mark idle enabled.

Flag or sync idle enabled.

AUTOSYNC HDLC ADDRESS

Type:

Register

Format:

AT [cmds] S20=n [cmds]

Default:

0

Range:

0-255

Unit:

Unidentified

Description:

Sets the HDLC address or BSC character.

COUNTRY CODE

Type:

Configuration

Format:

AT [cmds] *NCnn [cmds]

Description:

Changes the country code of the modem to nn.

DIAL

Type:

Immediate

Format:

AT [cmds] D<#> [cmds]

Description:

Dials telephone number according to any modifiers included in the string

Note:

Any combination of modifiers can be used to produce the desired dial functions in sequence.

Command

Function

DJ

MNP10 link will be negotiated at 1200bps for this call.

DK

MNP10 power level adjustment enabled for this call.

DL

Re-dial last number.

DP

Pulse dialing enabled.

DR

Answer mode enabled; originate mode disabled following handshake initiation.

DS=n

Dial stored telephone number n.

DT

Tone dialing enabled.

DW

Dialing resumed following dial tone detection.

D,

Dialing paused for amount of time specified in S8 register.

D"WXY"

Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad.

D!

Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.

D@

Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.

D$

Wait for prompt tone detection function enabled. Modem waits for prompt tone for amount of time specified by the S7 command.

D;

Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

D^

Calling tone toggled from current setting for this call.

PULSE DIAL CODE

Type:

Configuration

Format:

AT [cmds] *Zn [cmds]

Description:

Sets the currently active pulse dialing code.

Command

Function

í *Z0

Use dial code 0.

*Z1

Use dial code 1.

DISPLAY STORED NUMBERS

Type:

Immediate

Format:

AT [cmds] \F [cmds]

Description:

Displays all stored phone numbers.

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options.

Command

Function

&K0

Flow control disabled.

í &K3

RTS/CTS flow control enabled.

&K4

XON/XOFF flow control enabled.

&K5

Transparent XON/XOFF flow control enabled.

&K6

RTS/CTS and XON/XOFF flow control enabled.

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem model and speed

I1

Reports ROM checksum

I2

Tests and reports ROM checksum

I3

Reports firmware revision.

I5

Reports country code.

REQUEST LIST OF FORBIDDEN NUMBERS

Type:

Immediate

Format:

AT [cmds] *B [cmds]

Description:

Requests the list of forbidden numbers from the modem.

REQUEST LIST OF DELAYED NUMBERS

Type:

Immediate

Format:

AT [cmds] *D [cmds]

Description:

Requests the list of delayed numbers from the modem.