Visit our newest sister site!
Hundreds of free aircraft flight manuals
Civilian • Historical • Military • Declassified • FREE!


TUCoPS :: Phreaking Cellular - Other Manufacturers :: walker01.txt

Walker WMCD 8000 Programming




WALKER WMCD 8000

NOTES:  This unit has 8 NAMS
        The ESN prefix is 162 decimal & A5 hex.
        Walker: 1-800-251-1414

This unit is basically a Technophone PC 105, it can only be handset
programed if the firmware has been updated.  If you can not access
programing mode call Walker/Technophone at the number above for upgrade
information.

This unit requires a security code to access programing mode, this code is
based on the unit's electronic serial number.  The hardware serial number
on the phone is the ESN suffix, if not already known.

Take the last six digits of the ESN, rearange and subtract from 999999 to
get the security code:

         Original sequence: 1 2 3 4 5 6

         New sequence:      6 2 4 5 1 3

For example if the ESN is 16200002164 take 002164 and rearange to get
401602.  This number is then subtracted from 999999 to get a security code
of 598397.

Alternativly call 1-800-251-1414, ask for technical support and give them
the ESN.  They will convert it for you!

Having obtained the security code continue with the following steps:

1.  Turn phone on by pressing RCL.

NOTE:
    If phone powers up locked enter: FOUR DIGIT LOCK CODE, RCL to unlock.
    If lock code is unknown install new code by pressing:
    * SIX DIGIT SEC CODE, NEW LOCK CODE *
    You can disable the auto lock feature by entering:
    * SIX DIGIT SEC CODE * *

2.  Enter # S S S S S S # # 9 5 3 7 3 9 # up arrow # 9 9 # # (where SSSSSS
    is the security code).

3.  Turn phone off by pressing the up arrow key and LOCK.

4.  Turn phone on again and it should display "Which NAM?", if it does not
    review the security code and try again.

5.  Enter the NAM you want to program, NAMs are numbered 0 through 7,
    followed by the * key.

6.  The first data entry will appear.

7.  Press the UP ARROW key to store and increment the step number.

8.  Press SND after step 07 when display reads "Save NAM?" to store the new
    data, phone will revert to "Which NAM?" at which point you can press
    END to complete and exit, or select another NAM.


PROGRAMING DATA:

STEP#    #OF DIGITS/RANGE    DISPLAY          DESCRIPTION

01       00000 - 32767       AreaID#?         SYSTEM ID
02       10 DIGITS           Phone Number?    AREA CODE AND PHONE NUMBER
03       2 DIGITS            Overload Class?  ACCESS OVERLOAD CLASS
04       2 DIGITS            Group ID Mark?   GROUP ID (10 IN USA)
05       1 ONLY              EXP?
06       333 OR 334          IPCH?            INITIAL PAGING CHANNEL
07       3 ALPHA NUMERIC     System Ident?    SEE BELOW

Entry 07 is a convienience feature to distinguish between NAMs, you may
enter a three letter abbreviation to identify each NAM.  For instance enter
SFO for San Francisco.  Use the letters on the keypad, each time you press
a key the display will alternate.  For example the "2" key will scroll "2",
"A", "B", "C".  Press STO when the letter you want appears on the display.
To store SFO enter 7777 STO, 3333 STO, 6666 STO. 


TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2014 AOH