%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
%+% UNDER SURVEILLANCE +%+
%+% - +%+
%+% PHONE TAPPING +%+
%+% - +%+
%+% BY +%+
%+% THE DARK KNIGHT +%+
%+% - +%+
%+% 11/3/90 +%+
%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
DISCLAIMER:
The author takes no responsiblity for, nor does he assume any liability for,
damages resulting from the use of information in this document. This
document is for informational purposes only.
WARNING:
Connection of unauthorised equipment to a public (or indeed private system is
illegal and could lead to prosecution.
INTRODUCTION:
Now with the warnings over here is the equipment. Because of the highly
sophisticated nature of the modern telephone network, the installation of the
tap is a very tricky business indeed. It will take a capacitor (100nf), a
pair of high impedance headphones, anything up to two crocodile clips and at
least twelve seconds of concentrated effort. (See fig. 1)
FIG 1:
X---------------*---------------------------Y
phone lines |
|
X---------------|----------*----------------Y
| |
--- |
capacitor --- |
| |
|HEADPHONES|
One alternative to hanging around waiting for the telephone to answer is to
connect up a tape recorder. Now we come to the really sophisticated
electronics: since it is waste of tape to run the recorder continuosly, it is
useful to switch it on only when the phone is being used. Voice activated
switches? Why bother. A relay will do the trick, connected in series with
one of the lines. See plans on how to build a TAN box. There are plenty
around.
RADIO BUGS:
The next step up is some kind of radio bug. In the days not so long ago when
the BT issue phone was a wedge of cheese shaped affair with a dial on the
front, a favourite bugging device used to be the 'drop in' mike. The handset
microphone was a carbon granule device, quite bulky but easy to remove;
unscrew the mouthpiece, slip off a pair of wires from their terminals and its
out. The crafty buggers found a much better use for all that space than
filling it with carbon granuals. Buying microphones from the very same
people who supplied BT, they would empty out of the granuals, put in a much
smaller mike and would empty out the granuals, put in a much smaller mike and
a small radio transmitter, then seal the whole thing back together again.
Drop it into the handset and off you go. It is estimated that the numbers
made around the world ran into millions, so they were not uncommon! Still
used for bugging public telephones, but not much good for the wide varity of
office and home phones now in use.
SERIES AND PARALLEL BUGS:
Also very common and readily available are a variety of bugs which connect
either in series with one telephone wire or in parallel across the two.
The series bug has the advantage of only transmitting when the telephone is
used; the parallel one transmits continuosly in its crudest form (and most
commercial bugs are pretty crude) but can be a little more difficult to
detect by simple voltage measurements. Let's face it, it would be a trivial
matter to design a bug that is both triggered by use of the phone and
virtually impossible to detect by voltage measurements, but since almost
nobody takes seriously the idea that they may be a suitable target (do you
think you are, for instance?) and therefore won't be checking, why bother
with anything complicated?
See picture 1 and 2 for details. (End of file)
INFINITY TRANSMITTER:
The most exotic of the commonly used listerning devices is the 'infinity
transmitter', so called because once the victim can be snooped on from
anywhere in the world. Anywhere his phone can be reached by direct dialling,
that is. This is what you do: dial up the victim's number and hold your
little black mystery box close to the mouthpiece. In the simplest versions,
the mystery box just sends a tone down the line which is picked up by a
frequency selective circuit inside the bug. The mystery box activates the
infinity transmitter, which you previously attached to the victim's phone.
Once activated, the transmitter prevents the phone from ringing, and instead
sends down the line any sounds picked up by the victim's telephone, or by the
bug's own internal microphone.
This is how it works. On recieving the activating tone, the transmitter
passes enough current between the two lines to fool BT's equipment into
thinking that the phone has been answered, so the ringing tone is cancelled
and the line is opened. Once connection is made, all the bug has to do is to
modulate the line voltage in just the way the telephone itself would. Not
very difficult. The victim is entirly unaware of anything happening and,
with a hookswitch defeat installed, it could be his own telephone acting as
a microphone for the transmitter. The bug will automatically cut out if the
handset of the victim's phone is lifted, allowing it to be used normally.
See picture 2 for details. (End of file)
HOOK SWITCH DEFEAT:
Much simpler than the infinity transmitter, and used in much the same way, is
the hookswitch defeat. When you hang up the telephone, a switch disconnects
the handset... unless, that is, somebody has doctored the phone. The
simplest method is just to wire a resistor across the switch. In use you
phone the victim, apologise for having called up the wrong number, let him
hang up but keep your phone off the hook to hold open the connection.
Then you listen in. The sound level won't be very high, so you may need an
amplifier.
The difficulty with a plain hookswitch is that you need access to the
telephone itself and enough time to dismantle it. There is also the
possibility that an innocent caller may be slow to hang up and find himself
accidently eavesdroping. A bit of a giveaway. Hookswitch defeats are easy
to spot by anyone familiar with the insides of a telephone, but can often be
overlooked in inspection by a suspicious buggee since, unlike infinity
transmitters and the like, it could easily be part of the workings of the
phone.
Take the idea of 'looking as if it belongs' to its conclusion and you have
the 'lost' tranmitter. What you do is to find a large-ish component in the
telephone (or typewritter, calculator, or whatever) which itself uses any
signal you need access to. You then rush home to your garden shed and knock
up a device which not only does what this component does, but contains a
transmitter too. You package it to look exactly like the component you're
replacing. Then you pop back one night and swap the two around. Anyone
inspecting the phone or whatever will find it contains exactly the components
it should - no more and no less. The transmitter is really and truly lost.
This really is big league stuff - the kind of trick employees of rival
governments like to play on each other. Not the kind of thing you will
personally come across unless you have access to very valuable information
indeed. There's an American company called Fox which could be persuaded to
come up with the goodies if you approach them in the right way and have the
funds. They're in the phone book.
Okay that is about it for this document, but do bear in mind that BT are very
touchy about having alien equipment connected to their lines, even if it is
just a capacitor and headphones. And stay away from my phone, if you don't
mind!!
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ CIRCUIT DIAGRAMS: +
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
CIRCUIT 1:
SERIES PHONE BUG:
-=-=-=-=-=-=-=-=-
! ! W
! ! *-------*-------------*------* !
! ! ! ! C1 % TC & C4 %
! ! L1 &) R2 $ *------*----*
! ! ! ! ! !! ! ------ !
*------*-----(+)Q1 !
! *-*----! ~ + !-* ! ! ! !
! ! ! ! ! ! ! !
! R1 $ ! BR1 ! R3 $ C2 % R4 $ C3 %
! ! ! ! ! ! ! !
! *-*----! ~ - !---------*------*------*------*
! ! ------
! !
! !
! !
! !
! !
% = CAPACITOR
$ = RESISTOR
(+) = TRANSISTOR
& = TUNING COIL
&) = INDUCER
W = AERIAL
PARTS NEEDED:
R1 = 270K
R2 = 10K
R3 = 10K
R4 = 1K0
C1 = 15pF
C2 = 1nF0
C3 = 1nF0
C4 = 5pF0
Q1 = ZTX300
L1 = INDUCER 33uH
BR1= BRIDGE RECTIFIER
TC = TUNING COIL 3mm (4 OR 5 TURNS)
CIRCUIT 2:
PARALLEL PHONE BUG:
-=-=-=-=-=-=-=-=-=-
L1 W
! ! *-------*----*------&)----* !
! ! + = ! ! *---*--* ! !
! ! B1| ! R3$C2% C4%T1&--* %C6
! ! - = ! ! ! ! ! !
! ! R1 ! ! ! ! *--*-----*
*----+-$-*---+-%-*--(+)Q1 *--*--(+)Q2
! ! ! ! ! ! *--* *--*
! ! N1@ ! R2$ ! ! %C3 R4$ %C5
! ! ! ! ! ! ! ! ! !
! *---*---*---*---)&(--*------*--*
! ! A1
! !
! !
! !
% = CAPACITOR
$ = RESISTOR
(+) = TRANSISTOR
& = TUNING COIL
&) = INDUCER
)&( = AUDIO TRANSFORMER
=
| = BATTERY
=
@ = NEON
W = AERIAL
NOTE: A * indicates a join or a corner and a + indicates a wire cross over.
PARTS NEEDED:
R1 = 10K
R2 = 220K
R3 = 12K
R4 = 220R
C1 = 10nF
C2 = 47pF
C3 = 1nF5
C4 = 25pF
C5 = 1nF5
C6 = 10pF
Q1 = ZTX500
Q2 = ZTX300
N1 = NEON
A1 = AUDIO TRANSFORMER 25K )&( 1K0
B1 = 9V BATTB
L1 = INDUCER 1.8uH
TC = TUNING COIL 3mm (4 OR 5 TURNS)
CIRCUIT 3:
INFINITY TRANSMITTER:
-=-=-=-=-=-=-=-=-=-=-
*---------*-----------------------------------*----------*----*
! ! ! ! !
IMP ! $R2 $R8 $R11 !
A1 ! ! ! R9 ! !
*--)&(-----+-----* *---* *---+----$-----+--* !
! ! -----+-* ! ! ! ! ! ! ! !
! ! ! ! %C2 $R3 ! ! *--* ! ! !
! %C1 ! ! ! ! ! !Q4 ! ! ! ! !
! ! ! ! *-$-*--(+)Q2 *--(+) ! ! ! !
! ! --- ! ! !R7 ! ! C5 R5 R7 ! ! ! ZD1 ! ! !
*--+--*-|~ +|-* ! *--(+)Q1*---*-%-$-*---*->>-*---*-$-(+)Q3! *-<_<--(+) ! !
! | | ! ! ! ! ! ! ! ! ! ! ! ! Q5 ! !
! |BR1| ! %C3 ! $R4 %C4 &)L1%C6 %C7 $R6 ! ! $R10 ! !
! | | ! ! ! ! ! ! ! ! ! ! ! ! ! !
*--*----|~ -|---*---*---*---*---*-----*---*----*---*----*---*--* ! !
--- ! ! !
! ! !
D2 R12 ! ! !
*------------------------------<<----$-------------+----------* !
! R13 ! !
*--------------------$---* ! !
! ! ! !
! *---*---*---*-------+-------------------------+------------*
! ! ! ! ! ! !
! $R15%C10! ! ! !
! *---*--(+)Q8! ! !
*----*---(+)Q7! ! ! ! !
! ! ! ! *--(+)Q9 ! !
$R14 ! ! ! ! R18! !
C8 ! ! ! ! *---*-$-* !
*-%--*---(+)Q6 ! $R16 ! ! ! !
! ! ! ! ! ! ! ! !
()MIC%C9 ! ! %C11 $R17%C12%C13 !
! ! ! ! ! ! ! ! !
*----*----*----*---*-------*---*---*-------------------------*
% = CAPACITOR
$ = RESISTOR
(+) = TRANSISTOR
&) = INDUCER
)&( = AUDIO TRANSFORMER
() = MICROPHONE
>> = DIODE
<< = DIODE (POLARITY REVERSED)
<_< = ZENER DIODE
NOTE: A * indicates a join or corner and a + indicates a wire cross over.
PARTS NEEDED:
R2 = 33K
R3 = 33K
R4 = 4K7R
R5 = 4K7
R6 = 1M0
R7 = 100K
R8 = 68K
R9 = 82K
R10= 270K
R11= 68K
R12= 1K0
R13= 10K
R14= 390K
R15= 390K
R16= 10K
R17= 56R
R18= 15K
C1 = 4nF7 unpolarised
C2 = 10nF unpolarised
C3 = 10nF unpolarised
C4 = 10uF polarised +'ve to top
C5 = 10nF unpolarised
C6 = CHOOSE TO TUNE
C7 = 4uF7 polarised +'ve to top
C8 = 4uF7 polarised +'ve to right
C9 = 1nF0 unpolarised
C10= 1nF0 unpolarised
C11= 2uF2 polarised +'ve to top
C12= 47uF polarised +'ve to top
C13= 1uF0 polarised +'ve to top
Q1-Q9 = BC108
A1 = AUDIO TRANSFORMER 500R )&( 10K
D1 = 1N4148
D2 = 1N4148
ZD1= 6V8 ZENER DIODE
L1 = INDUCER 40mH
%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
% This document was written by The Dark Knight.+
% Contact me on ANGEL BBS - 0772 795476 24hrs. +
% or on EQUALISER BBS - 0923 662127 24hrs. +
%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+%+
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+Sysops: Feel free to place this on your download section, but please ensure+
+that this document and credits remain intact and unchanged. Thank you. +
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2024 AOH
