TUCoPS :: Scams :: countfit.txt

Counterfeiting Money (this won't work anymore BTW)

Counterfeiting Money     brought to you by DAI and INFERNO
----------------------   -*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*

Genuine currency is made by a process called "gravure", which
involves etching a metal block.  Since etching a metal block is
impossible to do by hand, photo offset printing comes into the

Photo offset printing starts by making negatives of the currency
with a camera, and putting the negatives on a piece of masking
material (usually orange in color).  The stripped negatives,
commonly called "flats", are then exposed to a lithographic plate
with an arc light plate maker.  The burned plates are then
developed with the proper developing chemical.  One at a time,
these plates are wrapped around the plate cylinder of the press.

The press to use should be an 11 by 14 offset, such as the AB Dick
360.  Make 2 negatives of the portrait side of the bill, and 1 of
the back side.  After developing them and letting them dry, take
them to a light table.  Using opaque on one of the portrait sides,
touch out all the green, which is the seal and the serial numbers.
The back side does not require any retouching, because it is all
one color.  Now, make sure all of the negatives are registered
(lined up correctly) on the flats.  By the way, every time you
need another serial number, shoot 1 negative of the portrait side,
cut out the serial number, and remove the old serial number from
the flat replacing it with the new one.

Now you have all 3 flats, and each represents a different color:
black, and 2 shades of green (the two shades of green are created
by mixing inks).  Now you are ready to burn the plates.  Take a
lithographic plate and etch three marks on it.  These marks must
be 2 and 9/16 inches apart, starting on one of the short edges.
Do the same thing to 2 more plates.  Then, take 1 of the flats and
place it on the plate, exactly lining the short edge up with the
edge of the plate.  Burn it, move it up to the next mark, and
cover up the exposed area you have already burned.  Burn that, and
do the same thing 2 more times, moving the flat up one more mark.
Do the same process with the other 2 flats (each on a separate
plate).  Develop all three plates.  You should now have 4 images
on each plate with an equal space between each bill.

The paper you will need will not match exactly, but it will do for
most situations.  The paper to use should have a 25% rag content.
By the way, Disaperf computer paper (invisible perforation) does
the job well.  Take the paper and load it into the press.  Be sure
to set the air, buckle, and paper thickness right.  Start with the
black plate (the plate without the serial numbers).  Wrap it
around the cylinder and load black ink in.  Make sure you run more
than you need because there will be a lot of rejects.  Then, while
that is printing, mix the inks for the serial numbers and the back
side.  You will need to add some white and maybe yellow to the
serial number ink.  You also need to add black to the back side.
Experiment until you get it right.  Now, clean the press and print
the other side.  You will now have a bill with no green seal or
serial numbers.  Print a few with one serial number, make another
and repeat.  Keep doing this until you have as many different
numbers as you want.  Then cut the bills to the exact size with a
paper cutter.  You should have printed a large amount of money by
now, but there is still one problem;  the paper is pure white.  To
dye it, mix the following in a pan:  2 cups of hot water, 4 tea
bags, and about 16 to 20 drops of green food coloring (experiment
with this).  Dip one of the bills in and compare it to a genuine
US bill.  Make the necessary adjustments, and dye all the bills.
Also, it is a good idea to make them look used.  For example,
wrinkle them, rub coffee grinds on them, etc.

As before mentioned, unless you are familiar with photo offset
printing, most of the information in this article will be fairly
hard to understand.  Along with getting a book on photo offset
printing, try to see the movie "To Live and Die in LA".  It is
about a counterfeiter, and the producer does a pretty good job of
showing how to counterfeit.  A good book on the subject is "The
Poor Man's James Bond".

If all of this seems too complicated to you, there is one other
method available for counterfeiting:  The Canon color laser
copier.  The Canon can replicate ANYTHING in vibrant color,
including US currency.  But, once again, the main problem in
counterfeiting is the paper used.  You will need to experiment
with it before using.  Remember, practice makes perfect.(****)

TUCoPS is optimized to look best in Firefox® on a widescreen monitor (1440x900 or better).
Site design & layout copyright © 1986-2024 AOH